- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33742EG (飛思卡爾半導體(中國)有限公司) System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver PDF資料下載
參數資料
| 型號： | MCZ33742EG |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 元件分類： | CAN |
| 英文描述： | System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver |
| 中文描述： | 系統基礎芯片的增強型（SBC）的高速CAN收發器 |
| 文件頁數： | 37/65頁 |
| 文件大?。?/td> | 1158K |
| 代理商： | MCZ33742EG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
37
33742
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Figure 23
illustrates how the wake-up signal is generated.
First the CAN signal is detected by a low consumption
receiver (WU receiver). Then the signal passes through a
pulse width filter, which discards the undesired pulses. The
pulse must have a width bigger than 0.5
μ
s and smaller than
500
μ
s to be accepted. When a pulse is discarded, the pulse
counter is reset
and no wake-up signal is generated. When a
pulse is accepted, the pulse counter is incremented and, after
three pulses, the internal wake-up signal is asserted.
Each one of the pulses must be spaced by no more than
500
μ
s. If not, the counter will be reset and no wake-up signal
will be generated. This is accomplished by the wake-up
timeout generator. The wake-up cycle is completed (and the
wake-up flag reset) when the CAN interface is brought to
CAN Normal mode.
Figure 23. Wake-Up Functional Block Diagram
CAN WAKE-UP REPORT
The CAN wake-up reporting depend upon the low power
mode the SBC is in.
If the SBC is placed into Sleep mode (VDD and V2 off), the
CAN wake-up or any wake-up results in the VDD regulator
turning on, leading to turning on the MCU supply and
releasing reset. If the 33742 is in Stop mode (V2 off and VDD
active), the CAN wake-up or any wake-up is signalled by a
pulse on the INT output. In addition the CANWU bit is set in
the CAN register.
If the SBC is in Normal or Standby mode and the CAN
interface is in Sleep mode with wake-up enabled, the CAN
wake-up is reported by the CANWU bit in the CAN register.
In the event the SBC is in Normal mode and CAN Sleep
mode with wake-up enabled, it is recommended that the user
check for the CANWU bit prior to placing the 33742 in Sleep
or Stop mode in case bus traffic has occurred while the CAN
interface was in Sleep mode.
After a CAN wake-up, a flag is set in the CAN register. Bit
CANWU reports the CAN wake-up event while the 33742
was in Sleep or Stop mode. This bit is set until the CAN is in
placed by SPI command into TXRX mode and the CAN
register can be read.
CAN BUS DIAGNOSTIC
The SBC can diagnose CANH or CANL lines short to
GND, shorts to VSUP or VDD.
As illustrated in
Figure 24
, several single-ended
comparators are implemented on the CANH and CANL bus
lines. These comparators monitor the bus voltage level in the
recessive and dominant states. This information is then
managed by a logic circuit to determine if a failure has
occurred and to report it.
Table 11
indicates the state of the
comparators in the event of bus failure and the state of the
drivers; that is, whether they are recessive or dominant.
+
Internal Wake-Up
Signal
Latch
RST
Time-out
RST
Counter
Pulse OK
Narrow
Pulse
Pulse Width
Filter
Time-out
Generator
Standby
WU Receiver
CANH
CANL
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33790EG | Two-Channel Distributed System Interface (DSI) Physical Interface Device |
| MCZ33793AEF | Distributed System Interface (DSI) Sensor Interface |
| MCZ33797EK | Four Channel Squib Driver IC |
| MCZ33800EK | Engine Control Integrated Circuit |
| MCZ33879AEK | Configurable Octal Serial Switch with Open Load Detect Current Disable |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33742EGR2 | 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33742SEG | 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33742SEGR2 | 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33780EG | 功能描述:多路器開關 IC DBUS MASTER RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MCZ33780EG | 制造商:Freescale Semiconductor 功能描述:DUAL DBUS MASTER INTERFACE 16SOIC |
發布緊急采購，3分鐘左右您將得到回復。