參數資料
型號： MCZ33742EG
廠商： 飛思卡爾半導體(中國)有限公司
元件分類： CAN
英文描述： System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver
中文描述： 系統基礎芯片的增強型（SBC）的高速CAN收發器
文件頁數： 22/65頁
文件大?。?/td> 1158K
代理商： MCZ33742EG
Analog Integrated Circuit Device Data
Freescale Semiconductor
22
33742
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 33742 and the 33742S are system basis chips (SBCs)
dedicated to automotive applications. Their functions include
the following:
One fully protected 5.0 V voltage regulator with 200 mA
total output current capability available at the VDD pin.
VDD regulator undervoltage reset function,
programmable window or time-out software watchdog
function.
Internal driver (V2) for an external series pass transistor
to implement a second 5.0 V voltage regulator.
Two running modes: Normal and Standby modes set by
the system microcontroller.
Sleep and Stop modes low power operating modes to
reduce an application’s current consumption while
providing a wake-up capability from the CAN interface,
L3 L0 wake-up inputs, or from a timer wake-up.
Programmable wake-up input and cyclic sense wake-
ups.
CAN high-speed physical bus interface with TXD and
RXD fault diagnostic capability and enhanced
protection features.
An SPI interface for use in communicating with a MCU
and Interrupt outputs to report SBC status, perform
diagnostics, and report wake-up events.
FUNCTIONAL PIN DESCRIPTION
RECEIVE AND TRANSMIT DATA (RXD AND TXD)
The RXD and TXD pins (receive data and transmit data
pins, respectively) are connected to a microcontroller’s CAN
protocol handler. TXD is an input and controls the CANH and
CANL line state (dominant when TXD is LOW, recessive
when TXD is HIGH). RXD is an output and reports the bus
state (RXD LOW when CAN bus is dominant, HIGH when
CAN bus is recessive).
Voltage Digital Drain (VDD)
The VDD pin
is the output pin
of the 5.0 V internal
regulator. It can deliver up to 200 mA. This output is protected
against overcurrent and overtemperature. It includes an
overtemperature pre-warning flag, which is set when the
internal regulator temperature exceeds 130°C typical. When
the temperature exceeds the overtemperature shutdown
(170°C typical), the regulator is turned off.
VDD
includes an undervoltage reset circuitry, which sets
the RST pin
LOW when VDD
is below the undervoltage reset
threshold.
RESET OUTPUT (RST)
The Reset pin RST is an output that is set LOW when the
device is in reset mode. The RST pin is set HIGH when the
device is not in reset mode. RST includes an internal pullup
current source. When RST is LOW, the sink current capability
is limited, allowing RST to be shorted to 5.0 V for software
debug or software download purposes.
INTERRUPT OUTPUT
(INT)
The Interrupt pin INT is an output that is set LOW when an
interrupt occurs. INT is enabled using the Interrupt Register
(INTR). When an interrupt occurs, INT stays LOW until the
interrupt source is cleared.
INT output also reports a wake-up event by a 10
μ
s typical
pulse when the device is in Stop mode.
VOLTAGE SOURCE 2 (V2)
The V2 pin is the input sense for the V2 regulator. It is
connected to the external series pass transistor. V2 is also
the 5.0 V supply of the internal CAN interface. It is possible to
connect V2 to an external 5.0 V regulator or to the VDD
output when no external series pass transistor is used. In this
case, the V2CTRL pin must be left open. Refer to
Figure 31,
SBC Typical Application Schematic
, page
52
.
VOLTAGE SOURCE 2 CONTROL (V2CTRL)
The V2CTRL pin is the output drive pin for the V2 regulator
connected to the external series pass transistor.
VOLTAGE SUPPLY (VSUP)
The VSUP pin is the battery supply input of the device.
HIGH-SIDE OUTPUT (HS)
The HS pin
is the internal high-side driver output. It is
internally protected against overcurrent and
overtemperature.
LEVEL 0-3 INPUTS (L0: L3)
The L0 : L3 pins can be connected to contact switches or
the output of other ICs for external inputs. The input states
can be read by SPI. These inputs can be used as wake-up
events for the SBC when operating in the Sleep or Stop
mode.
CAN HIGH AND CAN LOW OUTPUTS
(CANH AND CANL)
The CAN High and CAN Low pins are the interfaces to the
CAN bus lines. They are controlled by TXD input level, and
the state of CANH and CANL is reported through RXD output.
A 60
termination resistor is connected between CANH and
CANL pins.
相關PDF資料
PDF描述
MCZ33790EG Two-Channel Distributed System Interface (DSI) Physical Interface Device
MCZ33793AEF Distributed System Interface (DSI) Sensor Interface
MCZ33797EK Four Channel Squib Driver IC
MCZ33800EK Engine Control Integrated Circuit
MCZ33879AEK Configurable Octal Serial Switch with Open Load Detect Current Disable
相關代理商/技術參數
參數描述
MCZ33742EGR2 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33742SEG 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33742SEGR2 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33780EG 功能描述:多路器開關 IC DBUS MASTER RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MCZ33780EG 制造商:Freescale Semiconductor 功能描述:DUAL DBUS MASTER INTERFACE 16SOIC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*