- 您現在的位置：買賣IC網 > PDF目錄2097 > MCP6566RT-E/OT (Microchip Technology)IC COMPARATOR O-D 1.8V SOT23-5 PDF資料下載
參數資料
| 型號： | MCP6566RT-E/OT |
| 廠商： | Microchip Technology |
| 文件頁數： | 15/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC COMPARATOR O-D 1.8V SOT23-5 |
| 產品培訓模塊： | MCP656x |
| 標準包裝： | 1 |
| 類型： | 通用 |
| 元件數： | 1 |
| 輸出類型： | CMOS，開路漏極 |
| 電壓 - 電源，單路/雙路(±)： | 1.8 V ~ 5.5 V |
| 電壓 - 輸入偏移（最小值）： | 10mV @ 5.5V |
| 電流 - 輸入偏壓（最小值）： | 1pA @ 5.5V |
| 電流 - 輸出（標準）： | 50mA |
| 電流 - 靜態（最大值）： | 130µA |
| CMRR, PSRR（標準）： | 66dB CMRR，70dB PSRR |
| 傳輸延遲（最大）： | 80ns |
| 磁滯： | 5mV |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | SC-74A，SOT-753 |
| 安裝類型： | 表面貼裝 |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 681 (CN2011-ZH PDF) |
| 其它名稱： | MCP6566RT-E/OTDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
30
DS580F6
CS8406
SFMT0
SFMT1
4
5
Serial Audio Data Format Select (Input) - Selects the serial audio input port format. See Table 3 on
APMS
10 Serial Audio Data Port Master/Slave Select (
Input
) - APMS should be connected to VL to set serial
audio input port as a master or connected to GND to set the port as a slave.
HWCK0
HWCK1
20
27
OMCK Clock Ratio Select (Input) - Selects the ratio of OMCK to the input sample rate (Fs). A pull-up to
VL or pull-down to GND is required to set the appropriate mode. See Table 4 on page 28.
TCBLD
11 Transmit Channel Status Block Direction (
Input
) - Connect TCBLD to VL to set TCBL as an output.
Connect TCBLD to GND to set TCBL as an input.
TCBL
15
Transmit Channel Status Block Start (Input/Output) - When operated as output, TCBL is high during
the first sub-frame of a transmitted channel status block, and low at all other times. When operated as
input, driving TCBL high for at least three OMCK clocks will cause the next transmitted sub-frame to be
the start of a channel status block.
CEN
16
C Bit Enable (Input) - Determines how the channel status data bits are input. When CEN is low, Hard-
ware Mode A is selected, where the COPY/C, ORIG, EMPH and AUDIO pins are used to enter selected
channel status data. When CEN is high, Hardware Mode B is selected, where the COPY/C pin is used
to enter serial channel status data.
V
17 Validity Bit (
Input
) - In Hardware Modes A and B, the V pin input determines the state of the validity bit
in the outgoing AES3 transmitted data. This pin is sampled on both edges of the ILRCK.
U
18 User Data Bit (
Input
) - In Hardware Modes A and B, the U pin input determines the state of the user
data bit in the outgoing AES3 transmitted data. This pin is sampled on both edges of the ILRCK.
COPY/C
1
COPY Channel Status Bit/C Bit (Input) - In Hardware Mode A (CEN = 0), the COPY/C and ORIG pins
determine the state of the Copyright, Pro, and L Channel Status bits in the outgoing AES3 data stream,
see Table 2 on page 28. In Hardware Mode B, the COPY/C pin becomes the direct C bit input data pin,
which is sampled on both edges of LRCK.
EMPH
3
Pre-Emphasis Indicator (Input) - In Hardware Mode A (CEN = 0), the EMPHpin low sets the 3 empha-
sis channel status bits to indicate 50/15 s pre-emphasis of the transmitted audio data. If EMPH is high,
then the three EMPH channel status bits are set to 000, indicating no pre-emphasis.
AUDIO
19 Audio Channel Status Bit (
Input
) - In Hardware Mode A (CEN = 0), the AUDIO pin determines the
state of the audio/non audio Channel Status bit in the outgoing AES3 data stream.
ORIG
28
ORIG Channel Status Bit Control (Input) - In Hardware Mode A (CEN = 0), the ORIG and COPY/C
pins determine the state of the Copyright, Pro, and L Channel Status bits in the outgoing AES3 data
stream, see Table 2 on page 28.
TEST
2
7
8
Test Pins (Input) - These pins are unused inputs. It is recommended that these pins be tied to a supply
(VL or GND) to minimize leakage current. The CS8406 will operate correctly if these pins are left float-
ing, however current consumption from VL will increase by 25 A per TEST pin that is left floating.
相關PDF資料 |
PDF描述 |
|---|---|
| MHW10276N | IC CATV AMPLIFIER MODULE GAAS |
| MHW1244N | IC CATV AMP MOD 200MHZ 210MA 7P |
| MHW1254LAN | IC CATV AMP MOD 200MHZ 210MA 7P |
| MHW1254LN | IC CATV AMP MOD 65MHZ 95MA 7-PIN |
| MHW1303LAN | IC CATV AMP MOD 200MHZ 95MA 7PIN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP6566T-E/LT | 功能描述:校驗器 IC Singl 1.8V Opn Drain Comparator, E temp RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MCP6566T-E/MC | 功能描述:校驗器 IC SNGL 16V Open Drain Comparator E temp RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MCP6566T-E/MS | 功能描述:校驗器 IC SNGL 16V Open Drain Comparator E temp RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MCP6566T-E/OT | 功能描述:校驗器 IC Singl 1.8V Opn Drain Comparator, E temp RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MCP6566T-E/SN | 功能描述:校驗器 IC SNGL 16V Open Drain Comparator E temp RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。