- 您現在的位置：買賣IC網 > PDF目錄383588 > MCP23016 (Microchip Technology Inc.) 16-Bit I2C I/O Expander(16位I/O口擴展芯片) PDF資料下載
參數資料
| 型號： | MCP23016 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 16-Bit I2C I/O Expander(16位I/O口擴展芯片) |
| 中文描述： | 16位I2C I / O擴展（16位的I / O口擴展芯片） |
| 文件頁數： | 15/38頁 |
| 文件大?。?/td> | 578K |
| 代理商： | MCP23016 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
2003 Microchip Technology Inc.
DS20090B-page 15
MCP23016
1.9.3
READING THE REGISTERS
To read a MCP23016 register, the Master needs to
follow the requirements shown in Figure 1-6. First, the
device is selected by sending the slave address and
setting the R/W bit to logic ‘
0
’. The command byte is
sent after the address and determines which register
will be read. A restart condition is generated and the
device address is sent again with the R/W bit set to
logic ‘
1
’. The data register defined by the command
byte will be sent first, followed by the other register in
the register pair. The logic for register selection is the
same as explained in Write mode (
Section 1.9.2,
“Writing the Registers”
).
The falling edge of the ninth clock initiates the register
read action. The SCL clock will be held low while the
data is read from the register and is transferred to the
I
2
C bus control block by the Serializer/Deserializer
block.
The MCP23016 holds the clock low after the falling
edge of the ninth clock pulse. The configuration
registers (or port control registers) are read and the
value is stored. Finally, the clock is released to enable
the next transmission.
There is no limitation on the number of data bytes in
one read transmission. Figure 1-8 shows the case of
multiple byte read in one read operation. In this case,
the multiple writes are made to the same data pair.
FIGURE 1-6:
READ FROM
CONFIGURATION
REGISTER
Note:
The bus must remain free until after the
ninth clock pulse for a minimum of 12 μs
(see Table 2-5 and Figure 2-4).
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
0
0
A
A
A
D
S
0
R
W
=
A
D
D
D
D
D
D
D
A
A
C
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
0
0
A
A
A
D
S
0
R
W
=
A
D
D
D
D
D
D
D
A
A
D
M
1
2
3
4
5
6
7
8
9
D
D
D
D
D
D
D
D
A
D
L
P
S
S
S
d
S
d
相關PDF資料 |
PDF描述 |
|---|---|
| MCP3008(中文) | 2.7V 4-Channel/8-Channel 10-Bit A/D Converters With SPI Serial Interface(2.7V，4通道/8通道，10位，帶SPI串口的A/D轉換器) |
| MCP3004(中文) | 2.7V 4-Channel/8-Channel 10-Bit A/D Converters With SPI Serial Interface(2.7V，4通道/8通道，10位，帶SPI串口的A/D轉換器) |
| MCP3201-CIP | 2.7V 12-Bit A/D Converter with SPI Serial Interface |
| MCP3201-CIST | 2.7V 12-Bit A/D Converter with SPI Serial Interface |
| MCP3201 | 2.7V 12-Bit A/D Converter with SPI Serial Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP23016-I/ML | 功能描述:接口-I/O擴展器 16 bit In/Out RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MCP23016-I/SO | 功能描述:接口-I/O擴展器 16 bit In/Out RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MCP23016-I/SO | 制造商:Microchip Technology Inc 功能描述:I/O Expander IC |
| MCP23016-I/SP | 功能描述:接口-I/O擴展器 16 bit In/Out RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MCP23016-I/SP | 制造商:Microchip Technology Inc 功能描述:I/O Expander IC |
發布緊急采購，3分鐘左右您將得到回復。