- 您現在的位置：買賣IC網 > PDF目錄383588 > MCP23016 (Microchip Technology Inc.) 16-Bit I2C I/O Expander(16位I/O口擴展芯片) PDF資料下載
參數資料
| 型號： | MCP23016 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 16-Bit I2C I/O Expander(16位I/O口擴展芯片) |
| 中文描述： | 16位I2C I / O擴展（16位的I / O口擴展芯片） |
| 文件頁數： | 12/38頁 |
| 文件大?。?/td> | 578K |
| 代理商： | MCP23016 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
MCP23016
DS20090B-page 12
2003 Microchip Technology Inc.
1.8
Serializer/Deserializer
The
transfers data between the I
2
C bus and GPIO.
Serializer/Deserializer
block
converts
and
1.9
Interrupt Logic
The MCP23016 asserts the open-drain interrupt output
(INT) low when one of the port pins changes state. Only
those pins that are configured as an input can cause an
interrupt. Pins defined as an output have no effect on
INT. The interrupt will remain active until a read from
either the port (GPn) on which the interrupt occurred or
the INTCAPn register is performed. If the input returns
to its previous state before a read operation, it will reset
the interrupt and the INT pin output will tri-state. Each
8-bit port is read separately, so reading GP0 or
INTCAP0 will not clear the interrupt generated by GP1
or INTCAP1, and vice versa.
Input change activity on each port will generate an
interrupt and the value of the particular port will be
captured and copied into INTCAP0/INTCAP1. The
INTCAPn registers are only updated when an interrupt
occurs on INT. These values will stay unchanged until
the user clears the interrupt by reading the port or the
INTCAPn register.
If the input port value changes back to normal before a
user-read, the INT output will be reset. However, the
INTCAP0/INTCAP1 will still contain the value of the
port at the interrupt change. If the port value changes
again, it will re-activate the interrupt and the new value
will be captured.
The first interrupt on change event following an
interrupt RESET will result in a capture event. Any fur-
ther change event that occurs before the interrupt is
reset will not result in a capture event.
1.9.1
INTERRUPT EVENT DETECTION
The IARES bit controls the resolution for detecting an
interrupt-on-change event. If this bit is ‘
0
’ (default), the
maximum time for detecting a change of event is high,
which results in lower standby current. If this bit is ‘
1
’, it
takes less time for scanning the activity on the port and
results in higher standby current.
FIGURE 1-2:
READING PORTX AFTER
INTERRUPT EVENT
Port value
is captured
and written to
INTCAPn
PORT X
PORT X
GPx
INT
Port value
is captured
and written to
INTCAPn
Read GPx
or INTCAPn
相關PDF資料 |
PDF描述 |
|---|---|
| MCP3008(中文) | 2.7V 4-Channel/8-Channel 10-Bit A/D Converters With SPI Serial Interface(2.7V，4通道/8通道，10位，帶SPI串口的A/D轉換器) |
| MCP3004(中文) | 2.7V 4-Channel/8-Channel 10-Bit A/D Converters With SPI Serial Interface(2.7V，4通道/8通道，10位，帶SPI串口的A/D轉換器) |
| MCP3201-CIP | 2.7V 12-Bit A/D Converter with SPI Serial Interface |
| MCP3201-CIST | 2.7V 12-Bit A/D Converter with SPI Serial Interface |
| MCP3201 | 2.7V 12-Bit A/D Converter with SPI Serial Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP23016-I/ML | 功能描述:接口-I/O擴展器 16 bit In/Out RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MCP23016-I/SO | 功能描述:接口-I/O擴展器 16 bit In/Out RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MCP23016-I/SO | 制造商:Microchip Technology Inc 功能描述:I/O Expander IC |
| MCP23016-I/SP | 功能描述:接口-I/O擴展器 16 bit In/Out RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MCP23016-I/SP | 制造商:Microchip Technology Inc 功能描述:I/O Expander IC |
發布緊急采購，3分鐘左右您將得到回復。