參數資料
型號： MC80C52EXXX-12SC
廠商： TEMIC SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CDIP40
文件頁數： 44/125頁
文件大?。?/td> 6456K
代理商： MC80C52EXXX-12SC
21
2486AA–AVR–02/2013
ATmega8(L)
erwise no EEPROM write takes place. The following procedure should be followed when writing
the EEPROM (the order of steps 3 and 4 is not essential):
1.
Wait until EEWE becomes zero
2.
Wait until SPMEN in SPMCR becomes zero
3.
Write new EEPROM address to EEAR (optional)
4.
Write new EEPROM data to EEDR (optional)
5.
Write a logical one to the EEMWE bit while writing a zero to EEWE in EECR
6.
Within four clock cycles after setting EEMWE, write a logical one to EEWE
The EEPROM can not be programmed during a CPU write to the Flash memory. The software
must check that the Flash programming is completed before initiating a new EEPROM write.
Step 2 is only relevant if the software contains a boot loader allowing the CPU to program the
Flash. If the Flash is never being updated by the CPU, step 2 can be omitted. See “Boot Loader
programming.
Caution: An interrupt between step 5 and step 6 will make the write cycle fail, since the
EEPROM Master Write Enable will time-out. If an interrupt routine accessing the EEPROM is
interrupting another EEPROM access, the EEAR or EEDR Register will be modified, causing the
interrupted EEPROM access to fail. It is recommended to have the Global Interrupt Flag cleared
during all the steps to avoid these problems.
When the write access time has elapsed, the EEWE bit is cleared by hardware. The user soft-
ware can poll this bit and wait for a zero before writing the next byte. When EEWE has been set,
the CPU is halted for two cycles before the next instruction is executed.
Bit 0 – EERE: EEPROM Read Enable
The EEPROM Read Enable Signal EERE is the read strobe to the EEPROM. When the correct
address is set up in the EEAR Register, the EERE bit must be written to a logic one to trigger the
EEPROM read. The EEPROM read access takes one instruction, and the requested data is
available immediately. When the EEPROM is read, the CPU is halted for four cycles before the
next instruction is executed.
The user should poll the EEWE bit before starting the read operation. If a write operation is in
progress, it is neither possible to read the EEPROM, nor to change the EEAR Register.
The calibrated Oscillator is used to time the EEPROM accesses. Table 1 lists the typical pro-
gramming time for EEPROM access from the CPU.
Note:
1. Uses 1MHz clock, independent of CKSEL Fuse settings
Table 1. EEPROM Programming Time
Symbol
Number of Calibrated RC
Oscillator Cycles(1)
Typ Programming Time
EEPROM Write (from CPU)
8448
8.5ms
相關PDF資料
PDF描述
MD80C52TXXX-16SHXXX:D 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40
MR80C52CXXX-12SCR 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44
MQ80C52XXX-25 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQFP44
MD80C52EXXX-20SB 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CDIP40
MD80C52EXXX-16SBD 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40
相關代理商/技術參數
參數描述
MC80D21000G 制造商:COR 功能描述:RN
MC80F0104 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
MC80F0104B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
MC80F0104D 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
MC80F0204 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*