參數資料
型號: MC68331CFC16B1
廠商: Freescale Semiconductor
文件頁數: 17/84頁
文件大?。?/td> 0K
描述: IC MCU 32BIT 16MHZ 132-PQFP
標準包裝: 180
系列: M683xx
核心處理器: CPU32
芯體尺寸: 32-位
速度: 16MHz
連通性: EBI/EMI,SCI,SPI,UART/USART
外圍設備: POR,PWM,WDT
輸入/輸出數: 18
程序存儲器類型: ROMless
電壓 - 電源 (Vcc/Vdd): 4.5 V ~ 5.5 V
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 132-BQFP 緩沖式
包裝: 托盤
24
MC68331TS/D
When the on-chip clock synthesizer is used, system clock frequency is controlled by the bits in the upper
byte of SYNCR. Bits in the lower byte show status of or control operation of internal and external clocks.
The SYNCR can be read or written only when the CPU is operating at the supervisor privilege level.
W —Frequency Control (VCO)
This bit controls a prescaler tap in the synthesizer feedback loop. Setting the bit increases the VCO
speed by a factor of four. VCO relock delay is required.
X —Frequency Control Bit (Prescale)
This bit controls a divide by two prescaler that is not in the synthesizer feedback loop. Setting the bit
doubles clock speed without changing the VCO speed. There is no VCO relock delay.
Y[5:0] —Frequency Control (Counter)
The Y field controls the modulus down counter in the synthesizer feedback loop, causing it to divide by
a value of Y
+ 1. Values range from 0 to 63. VCO relock delay is required.
EDIV —E Clock Divide Rate
0 = ECLK frequency is system clock divided by 8.
1 = ECLK frequency is system clock divided by 16.
ECLK is an external M6800 bus clock available on pin ADDR23. Refer to 3.5 Chip Selects for more in-
formation.
SLIMP —Limp Mode Flag
0 = External crystal is VCO reference.
1 = Loss of crystal reference.
When the on-chip synthesizer is used, loss of reference frequency causes SLIMP to be set. The VCO
continues to run using the base control voltage. Maximum limp frequency is maximum specified system
clock frequency. X-bit state affects limp frequency.
SLOCK —Synthesizer Lock Flag
0 = VCO is enabled, but has not locked.
1 = VCO has locked on the desired frequency (or system clock is external).
The MCU maintains reset state until the synthesizer locks, but SLOCK does not indicate synthesizer
lock status until after the user writes to SYNCR.
RSTEN —Reset Enable
0 = Loss of crystal causes the MCU to operate in limp mode.
1 = Loss of crystal causes system reset.
STSIM —Stop Mode SIM Clock
0 = When LPSTOP is executed, the SIM clock is driven from the crystal oscillator and the VCO is
turned off to conserve power.
1 = When LPSTOP is executed, the SIM clock is driven from the VCO.
STEXT —Stop Mode External Clock
0 = When LPSTOP is executed, the CLKOUT signal is held negated to conserve power.
1 = When LPSTOP is executed, the CLKOUT signal is driven from the SIM clock, as determined by
the state of the STSIM bit.
3.4 External Bus Interface
The external bus interface (EBI) transfers information between the internal MCU bus and external de-
vices. The external bus has 24 address lines and 16 data lines.
The EBI provides dynamic sizing between 8-bit and 16-bit data accesses. It supports byte, word, and
long-word transfers. Ports are accessed through the use of asynchronous cycles controlled by the data
transfer (SIZ1 and SIZ0) and data size acknowledge pins (DSACK1 and DSACK0). Multiple bus cycles
may be required for a transfer to or from an 8-bit port.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC68331CFC16 IC MCU 32BIT 16MHZ 132-PQFP
C8051F587-IM IC 8051 MCU 96K FLASH 32-QFN
LPC11U24FBD48/401, IC MCU USB 48LQFP
LPC11U24FHN33/401, MCU USB 33HVQFN
MC68HC16Z1CPV16 IC MPU 1K RAM 16MHZ 144-LQFP
相關代理商/技術參數
參數描述
MC68331CFC20 制造商:Freescale Semiconductor 功能描述:
MC68331CFC20B1 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述:
MC68331CFC25 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述:
MC68331CFC25B1 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述:
MC68331CFV16 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:User’s Manual