- 您現在的位置：買賣IC網 > PDF目錄299463 > MBM29DL163TD12PBT (FUJITSU LTD) 1M X 16 FLASH 3V PROM, 120 ns, PBGA48 PDF資料下載
參數資料
| 型號： | MBM29DL163TD12PBT |
| 廠商： | FUJITSU LTD |
| 元件分類： | PROM |
| 英文描述： | 1M X 16 FLASH 3V PROM, 120 ns, PBGA48 |
| 封裝： | PLASTIC, FBGA-48 |
| 文件頁數： | 52/76頁 |
| 文件大?。?/td> | 1146K |
| 代理商： | MBM29DL163TD12PBT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
MBM29DL16XTD/BD-70/90/12
56
Extended Command
(1) Fast Mode
MBM29DL16XTD/BD has Fast Mode function. This mode dispenses with the initial two unclock cycles
required in the standard program command sequence by writing Fast Mode command into the command
register. In this mode, the required bus cycle for programming is two cycles instead of four bus cycles in
standard program command. (Do not write erase command in this mode.) The read operation is also executed
after exiting this mode. To exit this mode, it is necessary to write Fast Mode Reset command into the command
register. The first cycle must contain the bank address. (Refer to the Figure 28.) The VCC active current is
required even CE = VIH during Fast Mode.
(2) Fast Programming
During Fast Mode, the programming can be executed with two bus cycles operation. The Embedded Program
Algorithm is executed by writing program set-up command (A0H) and data write cycles (PA/PD). (Refer to
the Figure 28.)
(3) Extended Sector Group Protection
In addition to normal sector group protection, the MBM29DL16XTD/BD has Extended Sector Group
Protection as extended function. This function enable to protect sector group by forcing VID on RESET pin
and write a command sequence. Unlike conventional procedure, it is not necessary to force VID and control
timing for control pins. The only RESET pin requires VID for sector group protection in this mode. The extended
sector group protection requires VID on RESET pin. With this condition, the operation is initiated by writing
the set-up command (60H) into the command register. Then, the sector group addresses pins (A19, A18, A17,
A16, A15, A14, A13 and A12) and (A6, A1, A0) = (0, 1, 0) should be set to the sector group to be protected
(recommend to set VIL for the other addresses pins), and write extended sector group protection command
(60H). A sector group is typically protected in 250
s. To verify programming of the protection circuitry, the
sector group addresses pins (A19, A18, A17, A16, A15, A14, A13 and A12) and (A6, A1, A0) = (0, 1, 0) should be set
and write a command (40H). Following the command write, a logical “1” at device output DQ0 will produce
for protected sector in the read operation. If the output data is logical “0”, please repeat to write extended
sector group protection command (60H) again. To terminate the operation, it is necessary to set RESET pin
to VIH. (Refer to the Figures 20 and 29.)
(4) CFI (Common Flash Memory Interface)
The CFI (Common Flash Memory Interface) specification outlines device and host system software
interrogation handshake which allows specific vendor-specified software algorithms to be used for entire
families of devices. This allows device-independent, JEDEC ID-independent, and forward-and backward-
compatible software support for the specified flash device families. Refer to CFI specification in detail.
The operation is initiated by writing the query command (98H) into the command register. The bank address
should be set when writing this command. Then the device information can be read from the bank, and an
actual data of memory cell be read from the another bank. Following the command write, a read cycle from
specific address retrives device information. Please note that output data of upper byte (DQ8 to DQ15) is “0”
in word mode (16 bit) read. Refer to the CFI code table. To terminate operation, it is necessary to write the
read/reset command sequence into the register. (See Table 15.)
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29DL32TF70TN | 2M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| MBM29F800TA-70PFTN-E1 | 512K X 16 FLASH 5V PROM, 70 ns, PDSO48 |
| MBR-2051-1B5T | 51 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG |
| MBR-2069-0A1T | 69 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG |
| MBR-2069-0A2T | 69 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM29DL163TD-70PBT | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL163TD-70PFTN | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL163TD-70PFTR | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL163TD-90PBT | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL163TD-90PFTN | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
發布緊急采購，3分鐘左右您將得到回復。