- 您現在的位置：買賣IC網 > PDF目錄98010 > MB91F249PFV-GSE1 (FUJITSU LTD) 32-BIT, FLASH, 32 MHz, RISC MICROCONTROLLER, PQFP144 PDF資料下載
參數資料
| 型號： | MB91F249PFV-GSE1 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, FLASH, 32 MHz, RISC MICROCONTROLLER, PQFP144 |
| 封裝： | 20 X 20 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-144 |
| 文件頁數： | 8/84頁 |
| 文件大?。?/td> | 2105K |
| 代理商： | MB91F249PFV-GSE1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
MB91245/S Series
16
DS07-16803-3E
■ HANDLING DEVICES
Preventing Latch-up
Latch-up may occur in a CMOS IC, if a voltage greater than VCC pin or less than VSS pin is applied to input and
output pin, or if an above-rating voltage is applied between VCC pin and VSS pin. When latch-up occurs, it may
significantly increase the power supply current, and may cause thermal destruction of an element. When you
use a CMOS IC, be very careful not to exceed the maximum rating.
Treatment of Unused Input Pins
Do not leave an unused input pin open, since it may cause a malfunction. Handle by performing a pull-up or
pull-down with a resistance of 2 k
Ω or more. An unused I/O pin should be set to the output status and left open.
When set to the input status, it should be handled in the same way as an input pin.
About power supply pins
If there are multiple VCC and VSS pins, from the point of view of device design pins to be of the same potential
are connected inside the device to prevent such malfunctioning as latch-up. However, you must connect all the
pins to external power supply and a ground line to lower the electro-magnetic emission level, to prevent abnormal
operation of strobe signals caused by the rise in the ground level, and to conform to the total output current
rating. Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
Furthermore, it is also advisable to connect a ceramic bypass capacitor of approximately 0.1
μF between VCC
pin and VSS pin near this device.
This device incorporates a regulator. When using the device with 5V power supply, apply that power supply to
the VCC pin and always connect a 1
μF or greater capacitor to the VCC3C pin for the regulator.
5 V
VCC
5 V
GND
1
μF
AVCC
AVSS
VCC3C
VSS
AVRH
Example of power supply connection
相關PDF資料 |
PDF描述 |
|---|---|
| MB91F355APMT | 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP176 |
| MB91F367GB | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F368GB | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F463NCPMC-GSE1 | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP64 |
| MB91F464AAPMC-GSE2 | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91F264B | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller CMOS |
| MB91F264BPF-G | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller CMOS |
| MB91F264BPF-G-E1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller CMOS |
| MB91F264BPFV-G | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller CMOS |
| MB91F264BPFV-G-E1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller CMOS |
發布緊急采購，3分鐘左右您將得到回復。