參數資料
型號: MAX192
廠商: Maxim Integrated Products, Inc.
英文描述: Low-Power, 8-Channel,Serial 10-Bit ADC(8通道,133ksps串行10位A/D轉換器)
中文描述: 低功耗、8通道、串行10位ADC
文件頁數: 19/24頁
文件大?。?/td> 211K
代理商: MAX192
Figure 17, the Reference-Adjust Circuit, shows how to
adjust the ADC gain in applications that use the internal
reference. The circuit provides ±1.5% (±15LSBs) of
gain adjustment range.
Layout, Grounding, Bypassing
For best performance, use printed circuit boards.
Wire-wrap boards are not recommended. Board layout
should ensure that digital and analog signal lines are
separated from each other. Do not run analog and digi-
tal (especially clock) lines parallel to one another, or
digital lines underneath the ADC package.
Figure 18 shows the recommended system ground
connections. A single-point analog ground (“star”
ground point) should be established at AGND, sepa-
rate from the logic ground. All other analog grounds
and DGND should be connected to this ground. No
other digital system ground should be connected to
this single-point analog ground. The ground return to
the power supply for this ground should be low imped-
ance and as short as possible for noise-free operation.
High-frequency noise in the V
DD
power supply may
affect the high-speed comparator in the ADC. Bypass
these supplies to the single-point analog ground with
0.1μF and 4.7μF bypass capacitors close to the
MAX192. Minimize capacitor lead lengths for best sup-
ply-noise rejection. If the +5V power supply is very
noisy, a 10
resistor can be connected as a lowpass
filter, as shown in Figure 18.
High-S peed Digital Interfac ing
The MAX192 can interface with QSPI at high through-
put rates using the circuit in Figure 19. This QSPI cir-
cuit can be programmed to do a conversion on each of
the eight channels. The result is stored in memory with-
out taxing the CPU since QSPI incorporates its own
micro-sequencer.
Figure 20 details the code that sets up QSPI for
autonomous operation. In external clock mode, the
MAX192 performs a single-ended, unipolar conversion
on each of the eight analog input channels. Figure 21
shows the timing associated with the assembly code of
Figure 20. The first byte clocked into the MAX192 is the
control byte, which triggers the first conversion on CH0.
The last two bytes clocked into the MAX192 are all
zero, and clock out the results of the CH7 conversion.
M
Low-Power, 8-Channel,
S erial 10-Bit ADC
______________________________________________________________________________________
19
+5V
510k
100k
24k
0.01μF
12
REFADJ
MAX192
Figure 17. Reference-Adjust Circuit
+5V
GND
SUPPLIES
DGND
+5V
DGND
AGND
V
DD
DIGITAL
CIRCUITRY
MAX192
R* = 10
* OPTIONAL
Figure 18. Power-Supply Grounding Connection
相關PDF資料
PDF描述
MAX194 14-Bit, 85ksps ADC with 10礎 Shutdown(85ksps,單通道,14位串行A/D轉換器)
MAX1963 Low-Input-Voltage, 300mA LDO Regulators with RESETin SOT and TDFN
MAX1963ETT Low-Input-Voltage, 300mA LDO Regulators with RESETin SOT and TDFN
MAX1963EZT Low-Input-Voltage, 300mA LDO Regulators with RESETin SOT and TDFN
MAX1976 Low-Input-Voltage, 300mA LDO Regulators with RESETin SOT and TDFN
相關代理商/技術參數
參數描述
MAX1920ETT 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX1920ETT+T 功能描述:直流/直流開關轉換器 400mA Step-Down DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
MAX1920ETT-T 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX1920EUT 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE, 400MA STEP-DOWN DC-DC CONVERTERS - Rail/Tube
MAX1920EUT+ 制造商:Maxim Integrated Products 功能描述:CONV DC-DC SGL-OUT STEP DOWN 6PIN SOT-23 - Rail/Tube 制造商:Maxim Integrated Products 功能描述:Step-down DC-DC converter, MAX1920EUT+