參數資料
型號： MAX1403EVL11
廠商： Maxim Integrated Products
文件頁數： 21/36頁
文件大?。?/td> 0K
描述： EVAL KIT FOR MAX1403
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
ADC 的數量： 1
位數： 18
采樣率（每秒）： 480
數據接口： 串行
輸入范圍： ±VREF/增益
在以下條件下的電源（標準）： 16.9mW @ 480SPS
工作溫度： 0°C ~ 70°C
已用 IC / 零件： MAX1403
已供物品： 2 板，CD
MAX1403
+3V, 18-Bit, Low-Power, Multichannel,
Oversampling (Sigma-Delta) ADC
28
______________________________________________________________________________________
Offset-Correction DAC
The MAX1403 provides a coarse (3-bit plus sign) offset-
correction DAC at the modulator input. Use this DAC to
remove the offset component in the input signal, allow-
ing the ADC to operate on a more sensitive range. The
DAC offsets up to ±116.7% of the selected range in
±16.7% increments for unipolar mode, and up to
±58.3% of the selected range in ±8.3% increments for
bipolar mode. When a DAC value of 0 is selected, the
DAC is completely disconnected from the modulator
inputs and does not contribute any noise. Figures 8
and 9 show the effect of the DAC codes on the input
range and transfer function.
Clock Oscillator
The clock oscillator may be used with an external crystal
(or resonator) connected between CLKIN and CLKOUT,
or may be driven directly by an external oscillator at
CLKIN with CLKOUT left unconnected. In normal oper-
ating mode, the MAX1403 is specified for operation with
CLKIN at either 1.024MHz (CLK = 0) or 2.4576MHz
(CLK = 1, default). When operated at these frequencies,
the device may be programmed to produce frequency
response nulls at the local line frequency (either 60Hz or
50Hz) and the associated line harmonics.
In standby mode (STBY = 1) all circuitry, with the
exception of the serial interface and the clock oscillator,
is powered down. The interface consumes minimal
power with a static SCLK. Enter power-down mode
(including the oscillator) by setting the FULLPD bit in
the special-function register. When exiting a full-power
shutdown, perform a hardware reset or a software reset
after the master clock signal is established (typically
10ms when using the on-board oscillator with an exter-
nal crystal) to ensure that any potentially corrupted reg-
isters are cleared.
It is often helpful to use higher-frequency crystals or
resonators, especially for surface-mount applications
where the result may be reduced PC board area for the
oscillator component and a lower price or better com-
ponent availability. Also, it may be necessary to oper-
ate the part with a clock source whose duty cycle is not
close to 50%. In either case, the MAX1403 can operate
with a master clock frequency of up to 5MHz, and
includes an internal divide-by-2 prescaler to restore the
internal clock frequency to a range of up to 2.5MHz
with a 50% duty cycle. To activate this prescaler, set
the X2CLK bit in the control registers. Note that using
CLKIN frequencies above 2.5MHz in combination with
the X2CLK mode will result in a small increase in digital
supply current.
DAC CODE
D3:
D2:
D1:
D0:
INPUT
VOLTAGE
RANGE
(VREF = 1.25V
PGA = 000)
-7
1
-6
1
0
-5
1
0
1
-4
1
0
-3
1
0
1
-2
1
0
1
0
-1
1
0
1
0
+1
0
1
+2
0
1
0
+3
0
1
+4
0
1
0
+5
0
1
0
1
+6
0
1
0
+7
0
1
2.708V
2.50V
2.292V
2.083V
1.875V
1.667V
1.458V
1.25V
1.042V
0.833V
0.625V
0.416V
0.208V
0V
-0.208V
-0.416V
-0.625V
-0.833V
-1.042V
-1.25V
-1.458V
-1.667V
-1.875V
-2.083V
-2.292V
-2.50V
-2.708V
13/6 VREF/2PGA
2 VREF/2PGA
11/6 VREF/2PGA
10/6 VREF/2PGA
9/6 VREF/2PGA
8/6 VREF/2PGA
7/6 VREF/2PGA
VREF/2PGA
5/6 VREF/2PGA
4/6 VREF/2PGA
3/6 VREF/2PGA
2/6 VREF/2PGA
1/6 VREF/2PGA
0
-1/6 VREF/2PGA
-2/6 VREF/2PGA
-3/6 VREF/2PGA
-4/6 VREF/2PGA
-5/6 VREF/2PGA
-VREF/2PGA
-7/6 VREF/2PGA
-8/6 VREF/2PGA
-9/6 VREF/2PGA
-10/6 VREF/2PGA
-11/6 VREF/2PGA
-2 VREF/2PGA
-13/6 VREF/2PGA
MAXIMUM
INPUT
MINIMUM
INPUT
(U/B
= 1)
MINIMUM
INPUT
(U/B
= 0)
Figure 9. Input Voltage Range vs. DAC Code
ZERO-SCALE 2621
MIDSCALE 131072
NEGATIVE DAC STEP
SHIFTS THE TRANSFER
FUNCTION TOWARD
THE POSITIVE RAIL.
PGA = 3
DAC = 0
PGA = 0
DAC = 0
PGA = 3
DAC = +3
MAX CODE 262144
FULL-SCALE 259522
INPUT VOLTAGE RANGE
CODE
(V
AIN
-)-V
REF
AGND
(V
AIN
-)
-
V
REF
/8
-
V
REF
/16
(V
AIN
-)
-
V
REF
/8
-
V
REF
/16
(V
AIN
-)
-
V
REF
/8
(V
AIN
-)
+
V
REF
/8
V+
(V
AIN
-)
+
V
REF
(V
AIN-
)
Figure 8. Effect of PGA and DAC Codes on the Bipolar Transfer
Function
相關PDF資料
PDF描述
AD586KRZ-REEL7 IC VREF SERIES PREC 5V 8-SOIC
MAX1280EVC16 EVAL KIT FOR MAX1280
LGU2G221MELA CAP ALUM 220UF 400V 20% SNAP
MAX1284EVC16 EVALUATION SYSTEM FOR MAX1284
381LX682M025J012 CAP ALUM 6800UF 25V 20% SNAP
相關代理商/技術參數
參數描述
MAX1403EVSYSTEM 制造商:Maxim Integrated Products 功能描述:EVALUATION SYSTEM FOR THE MAX1403 - Boxed Product (Development Kits)
MAX1406C/D 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
MAX1406CAE 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
MAX1406CAE+ 功能描述:RS-232接口集成電路 15kV ESD-Protected 230kbps RS-232 LD/Rc RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
MAX1406CAE+T 功能描述:RS-232接口集成電路 15kV ESD-Protected 230kbps RS-232 LD/Rc RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*