參數資料
型號： MAX1403EVL11
廠商： Maxim Integrated Products
文件頁數： 18/36頁
文件大?。?/td> 0K
描述： EVAL KIT FOR MAX1403
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
ADC 的數量： 1
位數： 18
采樣率（每秒）： 480
數據接口： 串行
輸入范圍： ±VREF/增益
在以下條件下的電源（標準）： 16.9mW @ 480SPS
工作溫度： 0°C ~ 70°C
已用 IC / 零件： MAX1403
已供物品： 2 板，CD
MAX1403
+3V, 18-Bit, Low-Power, Multichannel,
Oversampling (Sigma-Delta) ADC
______________________________________________________________________________________
25
Table 14. REXT, CEXT Values for Less than 16-Bit Gain Error in Buffered (BUFF = 1)
Mode—All Modulator Sampling Frequencies (MF1, MF0 = XX); X2CLK = 0; CLKIN =
2.4576MHz
10
2
10
4
1
CEXT = 0pF
CEXT = 50pF
CEXT = 100pF
10
PGA GAIN
10
CEXT = 500pF
CEXT = 1000pF
CEXT = 5000pF
EXTERNAL RESISTANCE, REXT (k
)
10
16
10
32
8
10
64
10
128
10
Reference Input
The MAX1403 is optimized for ratiometric measure-
ments and includes a fully differential reference input.
Apply the reference voltage across REFIN+ and REFIN-,
ensuring that REFIN+ is more positive than REFIN-.
REFIN+ and REFIN- must be between AGND and V+.
The MAX1403 is specified with a +1.25V reference.
Modulator
The MAX1403 performs analog-to-digital conversion
using a single-bit, second-order, switched-capacitor
modulator. A single comparator within the modulator
quantizes the input signal at a much higher sample rate
than the bandwidth of the signal to be converted. The
quantizer then presents a stream of 1s and 0s to the
digital filter for processing, to remove the frequency-
shaped quantization noise.
The MAX1403 modulator provides 2nd-order frequency
shaping of the quantization noise resulting from the sin-
gle bit quantizer. The modulator is fully differential for
maximum signal-to-noise ratio and minimum suscepti-
bility to power-supply noise.
The modulator operates at one of a total of eight differ-
ent sampling rates (fM) determined by the master clock
frequency (fCLKIN), the X2CLK bit, the CLK bit, and the
modulator frequency control bits MF1 and MF0. Power
dissipation is optimized for each of these modes by
controlling the bias level of the modulator. Table 15
shows the input and reference sample rates.
PGA
A programmable gain amplifier (PGA) with a user-
selectable gain of x1, x2, x4, x8, x16, x32, x64, or x128
(Table 6) precedes the modulator. Figure 8 shows the
default bipolar transfer function with the following illus-
trated codes: 1) PGA = 0, DAC = 0; 2) PGA = 3, DAC =
0; or 3) PGA = 3, DAC = 3.
Output Noise
Tables 16a and 16b show the rms noise for typical out-
put frequencies (notches) and -3dB frequencies for the
MAX1403 with fCLKIN = 2.4576MHz. The numbers
given are for the bipolar input ranges with VREF =
+1.25V, with no buffer (BUFF = 0), and with the buffer
inserted (BUFF = 1). These numbers are typical and
are generated at a differential analog input voltage of 0.
Figure 7 shows graphs of Effective Resolution vs. Gain
and Notch Frequency. The effective resolution values
were derived from the following equation:
Effective Resolution = (SNRdB - 1.76dB) / 6.02
The maximum possible signal divided by the noise of
the device, SNRdB, is defined as the ratio of the input
full-scale voltage (i.e., 2 VREFIN / GAIN) to the output
rms noise. Note that it is not calculated using peak-to-
peak output noise numbers. Peak-to-peak noise num-
bers can be up to 6.6 times the rms numbers, while
effective resolution numbers based on peak-to-peak
noise can be 2.5 bits below the effective resolution
based on rms noise, as quoted in the tables.
The noise shown in Tables 16a and 16b is composed
of device noise and quantization noise. The device
noise is relatively low, but becomes the limiting noise
source for high gain settings. The quantization noise is
dependent on the notch frequency and becomes the
dominant noise source as the notch frequency is
increased.
相關PDF資料
PDF描述
AD586KRZ-REEL7 IC VREF SERIES PREC 5V 8-SOIC
MAX1280EVC16 EVAL KIT FOR MAX1280
LGU2G221MELA CAP ALUM 220UF 400V 20% SNAP
MAX1284EVC16 EVALUATION SYSTEM FOR MAX1284
381LX682M025J012 CAP ALUM 6800UF 25V 20% SNAP
相關代理商/技術參數
參數描述
MAX1403EVSYSTEM 制造商:Maxim Integrated Products 功能描述:EVALUATION SYSTEM FOR THE MAX1403 - Boxed Product (Development Kits)
MAX1406C/D 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
MAX1406CAE 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
MAX1406CAE+ 功能描述:RS-232接口集成電路 15kV ESD-Protected 230kbps RS-232 LD/Rc RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
MAX1406CAE+T 功能描述:RS-232接口集成電路 15kV ESD-Protected 230kbps RS-232 LD/Rc RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*