- 您現在的位置：買賣IC網 > PDF目錄384637 > M3822 (Mitsubishi Electric Corporation) Single Chip 8 Bits Microcomputer(8位單片機) PDF資料下載
參數資料
| 型號： | M3822 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | Single Chip 8 Bits Microcomputer(8位單片機) |
| 中文描述： | 單芯片8位單片機（8位單片機） |
| 文件頁數： | 38/52頁 |
| 文件大?。?/td> | 781K |
| 代理商： | M3822 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
38
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
3822 Group
X
IN
X
OUT
External oscillation
circuit
Open
V
CC
V
SS
C
CIN
C
COUT
Rf
Rd
X
CIN
X
COUT
X
CIN
X
COUT
X
IN
X
OUT
C
IN
C
OUT
C
CIN
C
COUT
Rf
Rd
CLOCK GENERATING CIRCUIT
The 3822 group has two built-in oscillation circuits. An oscillation
circuit can be formed by connecting a resonator between X
IN
and
X
OUT
(X
CIN
and X
COUT
). Use the circuit constants in accordance
with the resonator manufacturer's recommended values. No exter-
nal resistor is needed between X
IN
and X
OUT
since a feed-back re-
sistor exists on-chip. However, an external feed-back resistor is
needed between X
CIN
and X
COUT
.
To supply a clock signal externally, input it to the X
IN
pin and make
the X
OUT
pin open. The sub-clock X
CIN
-X
COUT
oscillation circuit
cannot directly input clocks that are externally generated. Accord-
ingly, be sure to cause an external resonator to oscillate.
Immediately after poweron, only the X
IN
oscillation circuit starts
oscillating, and X
CIN
and X
COUT
pins function as I/O ports. The
pull-up resistor of X
CIN
and X
COUT
pins must be made invalid to
use the sub-clock.
Frequency Control
Middle-speed mode
The internal clock
φ
is the frequency of X
IN
divided by 8.
After reset, this mode is selected.
High-speed mode
The internal clock
φ
is half the frequency of X
IN
.
Low-speed mode
The internal clock
φ
is half the frequency of X
CIN
.
A low-power consumption operation can be realized by stopping
the main clock X
IN
in this mode. To stop the main clock, set bit 5
of the CPU mode register to “1”.
When the main clock X
IN
is restarted, set enough time for oscil-
lation to stabilize by programming.
Note:
If you switch the mode between middle/high-speed and low-
speed, stabilize both X
IN
and X
CIN
oscillations. The suffi-
cient time is required for the sub-clock to stabilize, espe-
cially immediately after poweron and at returning from stop
mode. When switching the mode between middle/high-
speed and low-speed, set the frequency on condition that
f(X
IN
)>3f(X
CIN
).
Fig. 32 Ceramic resonator circuit
Fig. 33 External clock input circuit
Oscillation Control
Stop mode
If the STP instruction is executed, the internal clock
φ
stops at an
“H” level, and X
IN
and X
CIN
oscillators stop. Timer 1 is set to “FF
16
”
and timer 2 is set to “01
16
”.
Either X
IN
or X
CIN
divided by 16 is input to timer 1 as count
source, and the output of timer 1 is connected to timer 2.
The bits of the timer 123 mode register except bit 4 are cleared to
“0”. Set the timer 1 and timer 2 interrupt enable bits to disabled
(“0”) before executing the STP instruction.
Oscillator restarts at reset or when an external interrupt is re-
ceived, but the internal clock
φ
is not supplied to the CPU until
timer 2 underflows. This allows time for the clock circuit oscillation
to stabilize.
Wait mode
If the WIT instruction is executed, the internal clock
φ
stops at an
“H” level. The states of X
IN
and X
CIN
are the same as the state be-
fore the executing the WIT instruction. The internal clock restarts
at reset or when an interrupt is received. Since the oscillator does
not stop, normal operation can be started immediately after the
clock is restarted.
相關PDF資料 |
PDF描述 |
|---|---|
| M38B7 | Single Chip 8 Bits Microcomputer(8位單片機) |
| M3SW_A-2-50DR | High Isolation Switches SPDT, DC to 4.5 GHz |
| M3SW-2-50DR | High Isolation Switches SPDT, DC to 4.5 GHz |
| M3SWA-2-50DR | High Isolation Switches SPDT, DC to 4.5 GHz |
| M4034 | 3-INPUT VIDEO SWITCH |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38220E1DFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38220E1DFS | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38220E1DGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38220E1DHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38220E1DXXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。