參數資料
型號: M38049FFSP
廠商: Mitsubishi Electric Corporation
英文描述: SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述: 單芯片8位CMOS微機
文件頁數: 107/135頁
文件大?。?/td> 2055K
代理商: M38049FFSP
107
3803/3804 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
G
Erase command
Input command code 20
16
in the first transfer and command code
20
16
again in the second transfer. When this is done, the 3803/
3804 group executes an erase command. Erase is initiated at the
last rising edge of the serial clock. The BUSY pin is driven high
during the erase operation. Erase is completed within 9.5 ms as
measured by the internal timer, and the BUSY pin is pulled low.
Note that data 00
16
must be written to all memory locations before
executing the erase command.
Note:
A erase operation is not completed by executing the erase
command once. Always be sure to execute a erase verify
command after executing the erase command. When the fail-
ure is found in the verification, the user must repeatedly ex-
ecute the erase command until the pass in the verification.
Refer to Figure 92 for the erase flowchart.
Fig. 98 Timings at erasing
G
Erase verify command
The user must verify the contents of all addresses after complet-
ing the erase command. Input command code A0
16
in the first
transfer. Proceed and input the low-order 8 bits and the high-order
8 bits of the address and pull the OE pin low. When this is done,
the 3803/3804 group reads out the contents of the specified ad-
dress, and then latchs it into the internal data latch. When the OE
pin is released back high and serial clock is input to the SCLK pin,
the verify data that has been latched into the data latch is serially
output from the SDA pin.
Note:
If any memory location where the contents have not been
erased is found in the erase verify operation, execute the op-
eration of
erase
erase verify
over again. In this case,
however, the user does not need to write data 00
16
to memory
locations before erasing.
Fig. 99 Timings during erase verify
tw
E
SCLK
BUSY
OE
SDA
t
CH
t
EC
0 0 0 0 0 1 0 0
Command code input (20
16
) Command code input (20
16
)
0 0 0 0 0 1 0 0
Erase
H
L
SCLK
BUSY
OE
SDA
t
CH
A
0
A
7
A
8
A
15
D
0
D
7
t
CH
t
CREV
Command code input (A0
16
) Verify address input (L)
Verify address input (H)
Verify data output
t
WR
Verify read
t
RC
Note :
When outputting the verify data, the SDA pin is switched for output at the first falling edge of SCLK. The SDA pin is placed
in the floating state during the period of th
(C-E)
after the last rising edge of SCLK (at the 8th bit).
0 0 0 0 0 1 0 1
相關PDF資料
PDF描述
M38063M6-181GP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38067ECFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38062M3-156FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38062M3-158FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38063M6-255FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M38049RLSS 功能描述:DEV EMULATOR CHIP RAM 2KB 64SDIP RoHS:否 類別:編程器,開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:*
M3806 功能描述:電纜固定件和配件 LTSCG 625 BLACK RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度:
M3806 BK001 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 1000'
M3806 BK002 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 500'
M3806 BK005 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 100'