- 您現在的位置：買賣IC網 > PDF目錄370888 > M38037M6-XXXFP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M38037M6-XXXFP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 112/135頁 |
| 文件大?。?/td> | 2055K |
| 代理商： | M38037M6-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁當前第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁
112
3803/3804 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
G
Program command
When
“
40
16
”
is written to the flash command register, the 3803/
3804 group enters the program mode.
Subsequently to this, if the instruction (for instance, STA or LDM
instruction) for writing byte data in the address to be programmed
is executed, the control circuit of the flash memory executes the
program. The erase/program busy flag of the flash memory control
register is set to
“
1
”
when the program starts, and becomes
“
0"
when the program is completed. Accordingly, after the write in-
struction is executed, CPU can recognize the completion of the
program by polling this bit.
The programmed area must be specified beforehand by the erase/
program area select bits.
During programming, watchdog timer stops with
“
FFFF
16
”
set.
Note:
A programming operation is not completed by executing the
program command once. Always be sure to execute a pro-
gram verify command after executing the program command.
When the failure is found in this verification, the user must re-
peatedly execute the program command until the pass. Refer
to Figure 104 for the flow chart of the programming.
G
Program verify command
When
“
C0
16
" is written to the flash command register, the 3803/
3804 group enters the program verify mode. Subsequently to this,
if the instruction (for instance, LDA instruction) for reading byte
data from the address to be verified (i.e., previously programmed
address), the contents which has been written to the address ac-
tually is read.
CPU compares this read data with data which has been written by
the previous program command. In consequence of the compari-
son, if not agreeing, the operation of
“
program
→
program verify
”
must be executed again.
G
Erase command
When writing
“
20
16
”
twice continuously to the flash command reg-
ister, the flash memory control circuit performs erase to the area
specified beforehand by the erase/program area select bits.
Erase/program busy flag of the flash memory control register be-
comes
“
1
”
when erase begins, and it becomes
“
0" when erase
completes. Accordingly, CPU can recognize the completion of
erase by polling this bit.
Data
“
00
16
”
must be written to all areas to be erased by the pro-
gram and the program verify commands before the erase
command is executed.
During erasing, watchdog timer stops with
“
FFFF
16
”
set.
Note:
The erasing operation is not completed by executing the erase
command once. Always be sure to execute an erase verify
command after executing the erase command. When the fail-
ure is found in this verification, the user must repeatedly ex-
ecute the erase command until the pass. Refer to Figure 104
for the erasing flowchart.
G
Erase verify command
When
“
A0
16
" is written to the flash command register, the 3803/
3804 group enters the erase verify mode. Subsequently to this, if
the instruction (for instance, LDA instruction) for reading byte data
from the address to be verified, the contents of the address is
read.
CPU must erase and verify to all erased areas in a unit of ad-
dress.
If the address of which data is not
“
FF
16
”
(i.e., data is not erased)
is found, it is necessary to discontinue erasure verification there,
and execute the operation of
“
erase
→
erase verify
”
again.
Note:
By executing the operation of
“
erase
→
erase verify
”
again
when the memory not erased is found. It is unnecessary to
write data
“
00
16
”
before erasing in this case.
G
Reset command
The reset command is a command to discontinue the program or
erase command on the way. When
“
FF
16
”
is written to the command
register two times continuously after
“
40
16
”
or
“
20
16
”
is written to the
flash command register, the program, or erase command becomes
invalid (reset), and the 3803/3804 group enters the reset mode.
The contents of the memory does not change even if the reset com-
mand is executed.
DC Electric Characteristics
Note:
The characteristic concerning the flash memory part are the
same as the characteristic of the parallel I/O mode.
AC Electric Characteristics
Note:
The characteristics are the same as the characteristic of the
microcomputer mode.
相關PDF資料 |
PDF描述 |
|---|---|
| M38037M8-XXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38047M8-XXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38037M8-XXXHP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38037M8-XXXSP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M3803 | Single Chip 8 Bits Microcomputer(8位單片機) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38037M8108F | 制造商:Panasonic Industrial Company 功能描述:IC |
| M38037M8H-194HP#U0 | 制造商:Renesas Electronics Corporation 功能描述:8BIT CISC - Trays |
| M38039FFHFP#U0 | 功能描述:IC 740 MCU FLASH 60K 64QFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M38039FFHHP | 功能描述:MCU 3/5V 56K+4K 64-LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| M38039FFH-HP#U | 制造商:Renesas Electronics Corporation 功能描述:8BIT 740 CISC 56KB FLASH 16.8MHZ 3.3/5V - Trays |
發布緊急采購，3分鐘左右您將得到回復。