參數資料
型號： M37531RSS
元件分類： 微控制器/微處理器
英文描述： 8-BIT, 8 MHz, MICROCONTROLLER, CDIP42
封裝： SHRINK, CERAMIC, PIGGY BACK, DIP-42
文件頁數： 15/76頁
文件大?。?/td> 1022K
代理商： M37531RSS
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7531 Group
MITSUBISHI MICROCOMPUTERS
22
Fig. 25 Continuous transmission operation of UART serial I/O
[Serial I/O1 control register] SIO1CON
The serial I/O1 control register consists of eight control bits for the
serial I/O1 function.
[UART control register] UARTCON
The UART control register consists of four control bits (bits 0 to 3)
which are valid when asynchronous serial I/O is selected and set the
data format of an data transfer. One bit in this register (bit 4) is al-
ways valid and sets the output structure of the P11/TxD pin.
[Serial I/O1 status register] SIO1STS
The read-only serial I/O1 status register consists of seven flags (bits
0 to 6) which indicate the operating status of the serial I/O function
and various errors.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer is read.
If there is an error, it is detected at the same time that data is trans-
ferred from the receive shift register to the receive buffer, and the
receive buffer full flag is set. A write to the serial I/O1 status register
clears all the error flags OE, PE, FE, and SE (bit 3 to bit 6, respec-
tively). Writing “11” to bits 7 and 6 of the serial I/O1 control register
initializes this register.
All bits of the serial I/O1 status register are initialized to “8116” at
reset.
[Transmit/Receive buffer register] TB/RB
The transmit buffer and the receive buffer are located at the same
address. The transmit buffer is write-only and the receive buffer is
read-only. If a character bit length is 7-bit, the MSB of data stored in
the receive buffer is "0".
[Baud Rate Generator] BRG
The baud rate generator determines the baud rate for serial transfer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate generator.
TSC=0
TBE=1
TBE=0
ST
D0
D1
SP
D0
D1
ST
SP
ST
1 : When the serial I/O1 enable bit (b7) is “1”, the transmit enable bit is “1”, and continuous transmit valid bit is “1”, writing on the
transmit buffer initiates continuous transmission of the same data.
2 : Select 0 for continuous transmit valid bit to stop continuous transmission.
The TXD pin will stop at high level after completing transmission of 1 byte.
3 : If the transmit buffer contents are rewritten during a continuous transmission, transmission of the rewritten data will be started after
completing transmission of 1 byte.
Notes
1 Start Bit
7 or 8 Data Bit
1 or 0 Parity Bit
1 or 2 Stop Bit
Transmit/Receive Clock
Transmit Buffer Register
Write Signal
Serial Output TXD
相關PDF資料
PDF描述
M37532E8FP 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO36
M37532M4-XXXGP 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32
M37536M4-XXXSP 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PDIP42
M37536E8SP 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDIP42
M37540E8FP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO36
相關代理商/技術參數
參數描述
M37531T-ADS 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Temporary Target Board
M37532E8FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37532M4 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37532M4-A17GP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37532M4-XXXFP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*