- 您現在的位置：買賣IC網 > PDF目錄45010 > M30240MC-XXXFP 16-BIT, MROM, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M30240MC-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, MICROCONTROLLER, PQFP80 |
| 封裝： | 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件頁數： | 23/125頁 |
| 文件大小： | 753K |
| 代理商： | M30240MC-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁
Mitsubishi microcomputers
M16C / 24 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
121
CONFIDENTIAL
Preliminary Specifications REV.B
Specifications in this manual are tentative and subject to change
Usage Precautions
Stop Mode and Wait Mode
When returning from stop mode by hardware reset, RESET pin must be set to “L” level until main
clock oscillation is stabilized.
Interrupts
Reading address 0000016
When maskable interrupt is occurred, CPU read the interrupt information (the interrupt number and inter-
rupt request level) in the interrupt sequence.
The interrupt request bit of the certain interrupt written in address 0000016 is then set to “0”.
Reading address 0000016 by software sets enabled highest priority interrupt source request bit to “0”.
Though the interrupt is generated, the interrupt routine may not be executed.
Do not read address 0000016 by software.
Setting the stack pointer
The value of the stack pointer immediately after reset is initialized to 000016. Accepting an interrupt before
setting a value in the stack pointer may become a factor of runaway. Be sure to set a value in the stack
pointer before accepting an interrupt.
When using the NMI interrupt, initialize the stack point at the beginning of a program. Concerning the first
instruction immediately after reset, generating any interrupts including the NMI interrupt is prohibited.
The NMI interrupt
As for the NMI interrupt pin, an interrupt cannot be prohibited. Connect it to the VCC pin if unused.
Do not get either into stop mode or into wait mode with the NMI pin set to “L”.
Built-in PROM version
All built-in PROM versions
High voltage is required to program to the built-in PROM. Be careful not to apply excessive voltage. Be es-
pecially careful during power-on.
One Time PROM version
One Time PROM versions shipped in blank, of which built-in PROMs are programmed by users, are also pro-
vided. For these microcomputers, a programming test and screening are not performed in the assembly pro-
cess and the following processes. To improve their reliability after programming, we recommend to program
and test as flow shown in Figure 115 before use.
相關PDF資料 |
PDF描述 |
|---|---|
| M30240M4-XXXFP | 16-BIT, MROM, MICROCONTROLLER, PQFP80 |
| M30240M1-XXXFP | 16-BIT, MROM, MICROCONTROLLER, PQFP80 |
| M30245MC-XXXGP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| M30245FCGP | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
| M30260F3VGP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M30240S1 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240S1-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240S2 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240S2-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240S3 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。