- 您現在的位置：買賣IC網 > PDF目錄44994 > LTC3831IGN (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16 PDF資料下載
參數資料
| 型號： | LTC3831IGN |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 0.150 INCH, PLASTIC, SSOP-16 |
| 文件頁數： | 10/20頁 |
| 文件大?。?/td> | 208K |
| 代理商： | LTC3831IGN |
LTC3831
18
3831fb
APPLICATIONS INFORMATION
LAYOUT CONSIDERATIONS
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the LTC3831. These items are also illustrated graphically
in the layout diagram of Figure 10. The thicker lines show
the high current paths. Note that at 5A current levels or
above, current density in the PC board itself is a serious
concern. Traces carrying high current should be as wide as
possible. For example, a PCB fabricated with
2oz copper
requires a minimum trace width of
0.15” to carry 5A.
1. In general, layout should begin with the location of the
power devices. Be sure to orient the power circuitry so
that a clean power ow path is achieved. Conductor
widths should be maximized and lengths minimized.
After you are satised with the power path, the control
circuitry should be laid out. It is much easier to nd
routes for the relatively small traces in the control cir-
cuits than it is to nd circuitous routes for high current
paths.
2.
The GND and PGND pins should be shorted directly at
the LTC3831. This helps to minimize internal ground
disturbances in the LTC3831 and prevents differences
in ground potential from disrupting internal circuit
operation. This connection should then tie into the
ground plane at a single point, preferably at a fairly
quiet point in the circuit such as
close to the output
capacitors. This is not always practical, however, due
to physical constraints. Another reasonably good point
to make this connection is between the output capaci-
tors and the source connection of the bottom MOSFET
Q2. Do not tie this single point ground in the trace run
between the Q2 source and the input capacitor ground,
as this area of the ground plane will be very noisy.
3. The small-signal resistors and capacitors for frequency
compensation and soft-start should be located very close
to their respective pins and the ground ends connected
to the signal ground pin through a separate trace. Do
not connect these parts to the ground plane!
4. The VCC, PVCC1 and PVCC2 decoupling capacitors should
be as close to the LTC3831 as possible. The 4.7μF and
1μF bypass capacitors shown at VCC, PVCC1 and PVCC2
will help provide optimum regulation performance.
5. The (+) plate of CIN should be connected as close as
possible to the drain of the upper MOSFET, Q1. An ad-
ditional 1μF ceramic capacitor between VIN and power
ground is recommended.
6. The VFBpinisverysensitivetopickupfromtheswitching
node. Care should be taken to isolate VFB from possible
capacitive coupling to the inductor switching signal.
7. In a typical SSTL application, if the R+ pin is to be con-
nected to VDDQ, which is also the main supply voltage
for the switching regulator, do not connect R+ along the
high current ow path; it should be connected to the
SSTL interface supply output. R– should be connected
to the interface supply GND.
8. Kelvin sense IMAX and IFB at Q1’s drain and source
pins.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3833IUDC#PBF | SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC3833EFE#TRPBF | SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO20 |
| LTC3833EUDC#TRPBF | SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC3833EUDC#PBF | SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC3833IFE#PBF | SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3831IGN#PBF | 功能描述:IC SW REG CONTROLLR SYNC 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| LTC3831IGN#TRPBF | 功能描述:IC SW REG CONTROLLR SYNC 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| LTC3832-1ES8 | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC3832-1ES8#PBF | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| LTC3832-1ES8#TR | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。