參數資料
型號: LPC2923FBD100
廠商: NXP SEMICONDUCTORS
元件分類: 微控制器/微處理器
英文描述: ARM9 microcontroller with CAN, LIN, and USB
中文描述: 32-BIT, FLASH, 125 MHz, RISC MICROCONTROLLER, PQFP100
封裝: 14 X 14 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT407-1, LQFP-100
文件頁數: 18/84頁
文件大小: 551K
代理商: LPC2923FBD100
LPC2921_23_25_3
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 03 — 14 April 2010
18 of 84
NXP Semiconductors
LPC2921/2923/2925
ARM9 microcontroller with CAN, LIN, and USB
With dual buffering, a secondary buffer line is used, the output of the flash being
considered as the primary buffer. On a primary buffer, hit data can be copied to the
secondary buffer line, which allows the flash to start a speculative read of the next flash
word.
Both buffer lines are invalidated after:
Initialization
Configuration-register access
Data-latch reading
Index-sector reading
The modes of operation are listed in
Table 9
.
Table 9.
Synchronous timing
No buffer line
Single buffer line
6.8.2
Flash layout
The ARM processor can program the flash for ISP (In-System Programming) through the
flash memory controller. Note that the flash always has to be programmed by ‘flash words’
of 128 bits (four 32-bit AHB bus words, hence 16 bytes).
The flash memory is organized into eight ‘small’ sectors of 8 kB each and up to 11 ‘large’
sectors of 64 kB each. The number of large sectors depends on the device type. A sector
must be erased before data can be written to it. The flash memory also has sector-wise
protection. Writing occurs per page which consists of 4096 bits (32 flash words). A small
sector contains 16 pages; a large sector contains 128 pages.
Table 10
gives an overview of the flash-sector base addresses.
Table 10.
Flash memory
sector number
11
12
13
14
15
Flash read modes
for single (non-linear) reads; one flash-word read per word read
default mode of operation; most recently read flash word is kept until
another flash word is required
Asynchronous timing
No buffer line
Single buffer line
one flash-word read per word read
most recently read flash word is kept until another flash word is
required
on a buffer miss a flash read is done, followed by at most one
speculative read; optimized for execution of code with small loops
(less than eight words) from flash
most recently used flash word is copied into second buffer line; next
flash-word read is started; highest performance for linear reads
Dual buffer line, single
speculative
Dual buffer line, always
speculative
Flash sector overview
Sector size (kB)
Flash memory
address
0x2000 0000
0x2000 2000
0x2000 4000
0x2000 6000
0x2000 8000
LPC2921
LPC2923
LPC2925
8
8
8
8
8
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
相關PDF資料
PDF描述
LPC2925FBD100 ARM9 microcontroller with CAN, LIN, and USB
LPC2926FBD144 ARM9 microcontroller with CAN, LIN, and USB
LPC2927FBD144 ARM9 microcontroller with CAN, LIN, and USB
LPC2929FBD144 ARM9 microcontroller with CAN, LIN, and USB
LPC2930FBD208 ARM9 flashless microcontroller with CAN, LIN, and USB
相關代理商/技術參數
參數描述
LPC2923FBD100,551 功能描述:ARM微控制器 - MCU IC ARM9 MCU FLASH 256KB RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2925 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 microcontroller with CAN, LIN, and USB
LPC2925FBD100 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 microcontroller with CAN, LIN, and USB
LPC2925FBD100,551 功能描述:ARM微控制器 - MCU IC ARM9 MCU FLASH 512KB RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2926 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 microcontroller with CAN, LIN, and USB