- 您現在的位置：買賣IC網 > PDF目錄385497 > LPC2366FBD100 (NXP Semiconductors N.V.) ARM7 with 256 kB flash, 58 kB SRAM, Ethernet, USB 2.0 Device, CAN, and 10-bit ADC PDF資料下載
參數資料
| 型號： | LPC2366FBD100 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 數學處理器 |
| 英文描述： | ARM7 with 256 kB flash, 58 kB SRAM, Ethernet, USB 2.0 Device, CAN, and 10-bit ADC |
| 封裝： | LPC2366FBD100<SOT407-1 (LQFP100)|<<http://www.nxp.com/packages/SOT407-1.html<1<Always Pb-free,; |
| 文件頁數： | 9/18頁 |
| 文件大?。?/td> | 220K |
| 代理商： | LPC2366FBD100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
ES_LPC2366
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Errata sheet
Rev. 9 — 20 April 2011
9 of 18
NXP Semiconductors
ES_LPC2366
Errata sheet LPC2366
3.9 USB.1: USB_NEED_CLK is always asserted
Introduction:
The USB_NEED_CLK signal is used to facilitate going into and waking up from chip
Power Down mode. USB_NEED_CLK is asserted if any of the bits of the USBClkSt
register are asserted.
Problem:
The USB_NEED_CLK bit of the USBIntSt register (located at 0xE01F C1C0) is always
asserted, preventing the chip from entering Power Down mode when the USBWAKE bit is
set in the INTWAKE register (located at 0xE01F C144).
Work-around:
After setting the PCUSB bit in PCONP (located at 0xE01F C0C4), write 0x1 to address
0xFFE0C008. The USB_NEED_CLK signal will now function correctly. Writing to address
0xFFE0C008 only needs to be done once after each chip reset.
3.10 USB.2: U1CONNECT signal is not functional
Introduction:
U1CONNECT Signal (alternate function of P2.9) is part of the SoftConnect USB feature,
which is used to switch an external 1.5 KW resistor under the software control.
Problem:
The USB U1CONNECT alternate function does not work as expected.
Work-around:
Configure P2.9 as a GPIO pin, and use it to enable the pull-up resistor on the U1D+ pin.
3.11 USB.3: V
BUS
status input is not functional
Introduction:
The V
BUS
signal indicates the presence of USB bus power.
Problem:
The V
BUS
status input is not functional.
Work-around:
Configure P1.30 as a GPIO pin, and poll it to determine when V
BUS
goes to 0, signalling a
disconnect event.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC2367FBD100 | ARM7 with 512 kB flash, 58 kB SRAM, Ethernet and 10-bit ADC |
| LPC2368FBD100 | ARM7 with 512 kB flash, 58 kB SRAM, Ethernet, USB 2.0 Device, CAN, SD-MMC, and 10-bit ADC |
| LPC2377FBD144 | Single-chip 16-bit-32-bit microcontrollers; 512 kB flash with ISP-IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC-DAC |
| LPC2378FBD144 | Single-chip 16-bit-32-bit microcontrollers; 512 kB flash with ISP-IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC-DAC |
| LPC2387FBD100 | Single-chip 16-bit-32-bit MCU; 512 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC2366FBD100,551 | 功能描述:ARM微控制器 - MCU ARM7 256KF/USB/ENET RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2366FBD100/CP3298551 | 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| LPC2366FBD100551 | 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU 72MHZ LQFP-100 |
| LPC2366FBD100CP329 | 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| LPC2366FBD100-S | 制造商:NXP Semiconductors 功能描述:MCU 16-Bit/32-Bit LPC2000 ARM7TDMI-S RISC 256KB Flash 3.3V 100-Pin LQFP Tray |
發布緊急采購，3分鐘左右您將得到回復。