參數資料
型號： LC78626E
廠商： Sanyo Electric Co.,Ltd.
元件分類： 數字信號處理
英文描述： 16-bit fixed point DSP with Flash
中文描述： 具有閃存的 16 位定點 DSP
文件頁數： 23/32頁
文件大小： 475K
代理商： LC78626E
ATT DATA
100H
The audio output level = 20 log ————— [dB]
Because, for example, the time that it would take to increase the attenuation level from “00H” to “EEH” using the 4
step-up command would be as calculated below, this amount of time must be left before entering the next attenuation
level command:
238 level
×
4 Step-up
—————————
≈
21.6 ms (approx.)
44.1 kHz (LRSY)
* In order to prevent noise due to arithmetic overflow in the one-bit D/A converter, settings greater than EEH are
prohibited.
14 The Mute Output
Pin 51: MUTEL, Pin 57: MUTER
When the Mute control (MUTE –
∞
dB: $03) is exerted, and once the data for each channel has been continuously at
“0” for a specified amount of time, then this output goes high. Afterwards, when data is again entered, this output
immediately goes low.
15 The C2 Flag Output
Pin 46: C2F
C2F is an 8-bit unit flag that indicates the data error status.
16 The Digital OUT Output Circuit
Pin 39: DOUT
This is the digital audio interface output pin. Its output is in EIAJ format. This signal is interpolated, and the signal is
output through the MUTE circuit. Because this output pin is equipped with an internal driver, it can drive a
transformer directly.
* The digital OUT pin can be fixed low by inputting the DOUT OFF command.
* Of the DOUT data, the UBIT data can be fixed at low by entering the UBIT OFF command.
* By entering the CDROM-XA command, the DOUT pin can be switched to CD-ROM data that is not subjected to
interpolation or to mute control. (When this is done, the audio output is put into mute mode.) The ROMXA-RST
command returns the DOUT pin to the audio data output mode which is subject to interpolation and mute control.
(When this is done, the audio output mute is released.)
17 The Mute Control Circuit
The sound level can be muted (MUTE –
∞
dB) by the entry of the commands above. Because zero cross mute is used,
there is little noise during this operation. The zero cross determination is made in the range where the most significant
7 bits are all “1” or all “0.” Because the MUTE–12 dB command ($02) that was found in the LC78620E and 78621E
has been deleted, the digital attenuator is used and ATT DATA = 60 ($3C) is set.
No. 5692-23/32
LC78626E
Code
COMMAND
RES = low
$42
DOUT ON
G
G
$43
DOUT OFF
$40
UBIT ON
G
G
$41
UBIT OFF
$88
CDROM-XA
$8B
ROMXA-RST
G
G
Code
COMMAND
RES = low
$01
MUTE 0 dB
MUTE –
∞
dB
$03
G
G
44.1 kHz (normal speed), 88.2 kHz (double speed)
Start
Stop
相關PDF資料
PDF描述
LC78628 16-bit fixed point DSP with Flash
LC78628E 16-bit fixed point DSP with Flash
LC78630 16-bit fixed point DSP with Flash
LC78630E 16-bit fixed point DSP with Flash
LC78631 16-bit fixed point DSP with Flash
相關代理商/技術參數
參數描述
LC78626KE 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CD-Player Processor/Controller
LC78628 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Compact Disc Player DSP with Built-in HDCD Decoder
LC78628E 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Compact Disc Player DSP with Built-in HDCD Decoder
LC7863 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:DIGITAL SIGNAL PROCESSOR FOR COMPACT DISC PLAYERS
LC78630 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Compact Disk Player DSP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*