參數資料
型號： L9942XPTR
廠商： STMICROELECTRONICS
元件分類： 運動控制電子
英文描述： STEPPER MOTOR CONTROLLER, 2.5 A, PDSO24
封裝： LEAD FREE, POWER, SSO-24
文件頁數： 40/40頁
文件大?。?/td> 664K
代理商： L9942XPTR
L9942
Device description
2
Device description
2.1
Dual Power Supply: VS and VCC
The power supply voltage VS supplies the half bridges. An internal charge-pump is used to
drive the highside switches. The logic supply voltage VCC (stabilized) is used for the logic
part and the SPI of the device. Due to the independent logic supply voltage the control and
status information will not be lost, if there are temporary spikes or glitches on the power
supply voltage. In case of power-on (VCC increases from under voltage to VPOR OFF = 2.60
V, typical) the circuit is initialized by an internally generated power-on-reset (POR). If the
voltage VCC decreases under the minimum threshold (VPOR ON = 2.45 V, typical), the
outputs are switched to tristate (high impedance) and the internal registers are cleared.
2.2
Standby-Mode
The EN input has a pull-down resistor. The device is in standby mode if EN input isn't set to
a logic high level. All latched data will be cleared and the inputs and outputs are switched to
high impedance. In the standby mode the current at VS (VCC) is less than 3 A (1A) for
CSN = high (DO in tristate). If EN is set to a logic high level then the device will enter the
active mode. In the active mode the chargepump and the supervisor functions are activated.
2.3
Diagnostic Functions
All diagnostic functions (overload/-current, open load, power supply over-/undervoltage,
temperature warning and thermal shutdown) are internally filtered (tGL = 32s, typical) and
the condition has to be valid for a minimum time before the corresponding status bit in the
status registers will be set. The filters are used to improve the noise immunity of the device.
Open load and temperature warning function are intended for information purpose and will
not change the state of the bridge drivers. On contrary, the overload/-current and thermal
shutdown condition will disable the corresponding driver (overload/-current) or all drivers
(thermal shutdown), respectively. The microcontroller has to clear the status bit to reactivate
the bridge driver.
2.4
Over-voltage and Under-voltage Detection
If the power supply voltage VS rises above the over-voltage threshold VSOV OFF (typical 20
V), the outputs are switched to high impedance state to protect the load. When the voltage
VS drops below the undervoltage threshold VSUV OFF (UV-switch-OFF voltage), the output
stages are switched to the high impedance to avoid the operation of the power devices
without sufficient gate driving voltage (increased power dissipation). Error condition is
lached and the microcontroller needs to clear the status bits to reactivate the drivers.
2.5
Temperature Warning and Thermal Shutdown
If junction temperature rises above Tj TW a temperature warning flag is set which is
detectable via the SPI. If junction temperature increases above the second threshold Tj SD,
the thermal shutdown bit will be set and power DMOS transistors of all output stages are
相關PDF資料
PDF描述
L9951XPTR BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36
L9951TR BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36
L9952GXP 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36
L9952GXPTR 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36
L99H01QF BRUSH DC MOTOR CONTROLLER, PQFP32
相關代理商/技術參數
參數描述
L9946 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC Motor Controller/Driver
L9947 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:QUAD HALF-BRIDGE AND SINGLE HIGH-SIDE DRIVER
L9947L 制造商:STMicroelectronics 功能描述:
L9947S 功能描述:馬達/運動/點火控制器和驅動器 Quad Half Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
L9949 功能描述:功率驅動器IC Door Actuator RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*