- 您現在的位置：買賣IC網 > PDF目錄43901 > L7250 (STMICROELECTRONICS) VOICE COIL MOTOR CONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | L7250 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | VOICE COIL MOTOR CONTROLLER, PQFP64 |
| 封裝： | TQFP-64 |
| 文件頁數： | 26/46頁 |
| 文件大?。?/td> | 478K |
| 代理商： | L7250 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
L7250
32/46
3.8.2 Gain Calibration Procedure
The Bemf detector circuitry must be calibrated right before the beginning of any Load/Unload operation.
Because the coil resistance can vary up to 30% due to thermal effects, it is necessary to calibrate the gain of
the first stage depending on the ratio between the operating coil resistance value and the sense resistance val-
ue.
The output of the Bemf detector circuiry is:
Bemf = OutP - OutM - Rs*Ivcm ( 1+ Rm/Rs)
where: Rm = motor resistance
Rs = sensing resistance
If the Gain of the first stage is matching the ratio between the coil resistance at operating temperature and the
sense resistor, the Bemf measured is right the value generated by the VCM motion.
The gain trimming is done with the VCM in a stop position (no Bemf must be generated) with a certain amount
of current flowing into the coil; in this condition the gain must be adjusted in order to have zero voltage from the
Bemf circuitry.
The gain adjusting is splitted in two phases. A coarse calibration is obtained setting the external resistor divider
at the CalCoarse pin (29) following the relation:
Vcontrol = [0.21 + (Rm/Rs) / 28.8]
Vcontrol max. range = Vbg ±0.75V
Where: Vbg = bandgap voltage (typ = 1.25)
A fine calibration is obtained by writing the internal register 02H -> b[3:0]. The fine calibration is used to com-
pensate the variation of the VCM coil resistance according with operating temperature condition.
The calibration is implemented moving the Vcontrol voltage by a percentage indicated on the RLcal table at
pag.17.
3.8.3 VCM Bemf offset trimming
Due to the high gain necessary to implement the BEMF reconstruction, the inpact of the offset on the output
value is very high. For this reason dedicated circuitry, using the 5 MSB of the AD converter, has been integrated
in order to compensate this offset.
The flow chart below reported are describing the method to implement the offset calibration.
相關PDF資料 |
PDF描述 |
|---|---|
| L7980A | 3.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| L7980 | 3.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| L7980TR | 3.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| L7981ATR | SWITCHING REGULATOR, DSO8 |
| L7981TR | SWITCHING REGULATOR, DSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L7250E1.2 | 功能描述:電源開關 IC - 配電 DSD POWER RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| L7252E2.6 | 功能描述:電源開關 IC - 配電 DSD POWER RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| L725MAG | 制造商:Apex Tool Group 功能描述:TAPE, 1 IN. X 25 FT, 700 SERIES, MAGNETIC END HOOK 制造商:Lufkin 功能描述:TAPE MEASURE, MAGNETIC END HOOK 25FT 1IN; Tape Measure Type:Manual; Measuring Range Max:25ft; Blade Width:1"; Case Color:Orange; Tool Body Material:ABS; Blade Finish:Yellow Clad; Blade Length:25ft ;RoHS Compliant: NA |
| L728 | 制造商:BURNDY 功能描述:L-DIE |
| L7290 | 制造商:CIPS 功能描述:CUTTER OBLIQUE SEMI FLUSH 109MM |
發布緊急采購，3分鐘左右您將得到回復。