- 您現在的位置：買賣IC網 > PDF目錄43901 > L7250 (STMICROELECTRONICS) VOICE COIL MOTOR CONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | L7250 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | VOICE COIL MOTOR CONTROLLER, PQFP64 |
| 封裝： | TQFP-64 |
| 文件頁數： | 21/46頁 |
| 文件大?。?/td> | 478K |
| 代理商： | L7250 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
L7250
28/46
Considering a typical application with Rs = 0.25
, Lm = 0.75mH, Rm = 7.5, Gs = 4.5 Gpow = 8, Rf = 5.6K, Cc =
3.3nF, Rc = 33k we will obtain a bandwidth about 20kHz. To increase the bandwidth a different values of the external
components could be calculated following the above relation and taking in account the limitation introduced by the
second pole due to the error amplifier bandwidth (
ωt). This one has a typical value about 4MHz.
3.1 VCM Operating Modes and Control
At power-on-reset the VCM register is cleared and the VCM is in Unload/Retract mode.
Via serial port is possible to command the following modes: Unload/Retract, Tri-state (disable), Brake, Enable
Current Mode, Enable Voltage Mode, Offset Calibration
3.2 VCM Power Driver H-Bridge
The VCM driver is capable of high performance linear, class-AB, H-bridge operation with all power devices in-
ternal. The power amp stage is configured as a voltage amp with gain of 16. The H-bridge consists of 4 N-chan-
nel DMOS power transistors. Power is supplied to the H-bridge through the internal ISO-FET ( at pins VM
52,53), and ground returned via four VCMGND pins (5,6,43,44). Boosted gate drive for the high side drivers is
provided by the charge pump circuitry, with the boosted voltage at the VCP pin.
3.3 VCM Current Command 15 bit DAC
The VCM current command is defined by an internal linear, 2's complement, 15 bit DAC. The mid scale refer-
ence for the DAC, VREF25, is defined by an on-chip reference at 2.5V. VREF25 is the reference for the sense
amp and error amp in the VCM loop. Level shifting from VREF25 to VM/2 will be done in the power stage.
0x3FFF Max current flowing from VCMN to VCMP (current mode operation)
0x----
0x0001
0x0000 zero current
0xFFFF
0x----
0x4000 Max current flowing from VCMP to VCMN (current mode operation)
To write the 15 bit DAC the two register REG09H [14:8] and REG0AH [7:0] have to be referred.
At any time the MSB register is entered, to apply the modification also the LSB register must be write. Instead
writing only the LSB register its content will be immediatly visible on the DAC structure.
Then a double write sequence its necessary if the [14:8] bit have to be modified while it is possible to move the
DAC in a fine way (write of the [7:0] bit) with only one write sequence.
3.4 VCM Current Sense Amp
VCM current is sensed by a diff amp that amplifies and level shifts the voltage drop across an external resistor
in series with the VCM coil. The sense amp has a nominal differential voltage gain programmable through the
serial port bit Reg09H bit 7, and the output, VSENSE, is relative to VREF25 (pin 21). The amp has been design
to have high common mode rejection (over 70dB at DC), Power supply rejection over 60dB, and as low an input
offset as possible.
3.5 VCM Current Loop Error Amplifier
The VCM error amp gains up the difference between the current command voltage DAC_OUT and the current
sense voltage VSENSE. VCM current loop compensation is implemented externally with an RC network con-
nected across ERR_IN and ERR_OUT. The error amp output is referred to VREF25.
3.6 Error Amp Output Clamp
The error amp output swing is clamped in both directions (Vref25+/-3Vbe) to prevent wind-up of the integrating
compensation components around the error amp in the event of saturation.
相關PDF資料 |
PDF描述 |
|---|---|
| L7980A | 3.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| L7980 | 3.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| L7980TR | 3.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| L7981ATR | SWITCHING REGULATOR, DSO8 |
| L7981TR | SWITCHING REGULATOR, DSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L7250E1.2 | 功能描述:電源開關 IC - 配電 DSD POWER RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| L7252E2.6 | 功能描述:電源開關 IC - 配電 DSD POWER RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| L725MAG | 制造商:Apex Tool Group 功能描述:TAPE, 1 IN. X 25 FT, 700 SERIES, MAGNETIC END HOOK 制造商:Lufkin 功能描述:TAPE MEASURE, MAGNETIC END HOOK 25FT 1IN; Tape Measure Type:Manual; Measuring Range Max:25ft; Blade Width:1"; Case Color:Orange; Tool Body Material:ABS; Blade Finish:Yellow Clad; Blade Length:25ft ;RoHS Compliant: NA |
| L728 | 制造商:BURNDY 功能描述:L-DIE |
| L7290 | 制造商:CIPS 功能描述:CUTTER OBLIQUE SEMI FLUSH 109MM |
發布緊急采購，3分鐘左右您將得到回復。