- 您現在的位置：買賣IC網 > PDF目錄43901 > L7250 (STMICROELECTRONICS) VOICE COIL MOTOR CONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | L7250 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | VOICE COIL MOTOR CONTROLLER, PQFP64 |
| 封裝： | TQFP-64 |
| 文件頁數： | 22/46頁 |
| 文件大?。?/td> | 478K |
| 代理商： | L7250 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
29/46
L7250
3.6.1 Voltage Mode
In Voltage Mode, the VCM power outputs will apply a voltage to the VCM motor commanded by the VCM DAC.
This is implemented by tristating the sense amp and error amp outputs, and connecting DAC_OUT to
ERR_OUT with an internal switch (switch S2). Skipping the err_out amplifier the DAC command will enter the
power section without any inversion, then the DAC codification must be considered in opposite direction respect
to the current mode operation.
3.7 VCM Loop Offset Calibration Mode
The VCM Loop Calibration mode can be implemented following two different approach:
1) The VCM loop is enabled (sense amp, error amp, DAC), but the VCM power stage is tri-stated. Thus,
the sense amp is guaranteed to be monitoring a zero current condition.
To implement offset calibration, the current command is swept through zero by the controller ASIC.
Since the Gm loop is open, the error amp output will be saturated in one direction or the other depending
on the current command (to configurate the error opamp as a comparator the external compensation
network will be disconnected opening the switch S1). As the command sweeps through the zero current
command point, the error amp output will swing to the other extreme. The comparator senses the out-
put swing of the error amp, and through the serial port (Reg. 00H -> b6) interrupts the ASIC. The ap-
propriate DAC value corresponding to the trip point interrupt is the loop zero current offset.
Figure 9. VCM Current Loop Offset Calibration 1
Set VCM Offset Calibration
Write Reg.03H
VCMState[2:0] = 101
START
VCM Current Loop
Offset Calibration Routine
UPDATE 15 Bit DAC
Write Reg.09H
dac[14:0]= DAC_VAL
EXIT
VCM Current Loop
Offset Calibration Routine
Select
Sense Amplifier
Gain
4.5 V/V
16 V/V
DAC_VAL = 0
Flag1 = 0 , Flag2 = 0
Set SenseAmpl.Gain
Write Reg.09H
GainSW bit = 0
Set SenseAmpl.Gain
Write Reg.09H
GainSW bit = 1
Read Error Ampl Output
Read Reg.00H
VCMcalOut bit value
VCMcalOut = 0
NO
YES
DAC_VAL = DAC_VAL +1
Flag2 =1
Flag1 = 1
DAC_VAL = DAC_VAL -1
Flag2 = 1
YES
NO
YES
NO
Store the DAC_VAL
as the zero loop offset
* DAC_VAL is in 2 complement format
相關PDF資料 |
PDF描述 |
|---|---|
| L7980A | 3.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| L7980 | 3.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| L7980TR | 3.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| L7981ATR | SWITCHING REGULATOR, DSO8 |
| L7981TR | SWITCHING REGULATOR, DSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L7250E1.2 | 功能描述:電源開關 IC - 配電 DSD POWER RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| L7252E2.6 | 功能描述:電源開關 IC - 配電 DSD POWER RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| L725MAG | 制造商:Apex Tool Group 功能描述:TAPE, 1 IN. X 25 FT, 700 SERIES, MAGNETIC END HOOK 制造商:Lufkin 功能描述:TAPE MEASURE, MAGNETIC END HOOK 25FT 1IN; Tape Measure Type:Manual; Measuring Range Max:25ft; Blade Width:1"; Case Color:Orange; Tool Body Material:ABS; Blade Finish:Yellow Clad; Blade Length:25ft ;RoHS Compliant: NA |
| L728 | 制造商:BURNDY 功能描述:L-DIE |
| L7290 | 制造商:CIPS 功能描述:CUTTER OBLIQUE SEMI FLUSH 109MM |
發布緊急采購，3分鐘左右您將得到回復。