- 您現在的位置：買賣IC網 > PDF目錄1931 > KSZ8051MLLI TR (Micrel Inc)TXRX PHY 10/T100 3.3V MII 48LQFP PDF資料下載
參數資料
| 型號： | KSZ8051MLLI TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 27/51頁 |
| 文件大小： | 0K |
| 描述： | TXRX PHY 10/T100 3.3V MII 48LQFP |
| 特色產品： | KSZ8051/8031/8021 Series |
| 標準包裝： | 1 |
| 類型： | PHY 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | MII |
| 電源電壓： | 1.8V，2.5V，3.3V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 標準包裝 |
| 配用： | 576-3864-ND - BOARD EVALUATION FOR KSZ8051MLL |
| 其它名稱： | 576-3888-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
2009 Microchip Technology Inc.
DS22147A-page 33
MCP4017/18/19
5.0
SERIAL INTERFACE -
I2C MODULE
A 2-wire I2C serial protocol is used to write or read the
digital potentiometer’s wiper register. The I2C protocol
utilizes the SCL input pin and SDA input/output pin.
The I2C serial interface supports the following features.
Slave mode of operation
7-bit addressing
The following clock rate modes are supported:
- Standard mode, bit rates up to 100 kb/s
- Fast mode, bit rates up to 400 kb/s
Support Multi-Master Applications
The serial clock is generated by the Master.
The I2C Module is compatible with the Phillips I2C
specification. Phillips only defines the field types, field
lengths, timings, etc. of a frame. The frame content
defines the behavior of the device. The frame content
for the MCP4017, MCP4018, and MCP4019 devices
are defined in this section of the Data Sheet.
FIGURE 5-1:
Typical Application I2C Bus
Configurations.
Refer to Section 2.0 “Typical Performance Curves”,
AC/DC Electrical Characteristics table for detailed input
threshold and timing specifications.
5.1
I2C I/O Considerations
I2C specifications require active low, passive high
functionality on devices interfacing to the bus. Since
devices may be operating on separate power supply
sources, ESD clamping diodes are not permitted. The
specification recommends using open drain transistors
tied to VSS (common) with a pull-up resistor. The
specification makes some general recommendations
on the size of this pull-up, but does not specify the
exact value since bus speeds and bus capacitance
impacts the pull-up value for optimum system
performance.
Common pull-up values range from 1 kΩ to a max of
~10 kΩ. Power sensitive applications tend to choose
higher values to minimize current losses during
communication but these applications also typically
utilize lower VDD.
The SDA and SCL float (are not driving) when the
device is powered down.
A "glitch" filter is on the SCL and SDA pins when the pin
is an input. When these pins are an output, there is a
slew rate control of the pin that is independent of device
frequency.
5.1.1
SLOPE CONTROL
The device implements slope control on the SDA
output. The slope control is defined by the fast mode
specifications.
For Fast (FS) mode, the device has spike suppression
and Schmidt trigger inputs on the SDA and SCL pins.
Single I2C Bus Configuration
Host
Controller
Device 1
Device 3
Device n
Device 2
Device 4
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8051MNLI | TXRX PHY 10/T100 3.3V 32QFN |
| KSZ8051RNLI TR | TXRX PHY 10/T100 3.3V RMII 32QFN |
| KSZ8692XPB | IC ARM9 PHY 10/100MBPS 400-PBGA |
| KSZ8695P | IC ARM9 W/MMU PHY 10/100 289PBGA |
| KSZ8695X | IC SWITCH 10/100 5PORT 208PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8051MNL | 功能描述:TXRX PHY 10/T100 3.3V MII 32-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| KSZ8051MNL TR | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ MII Support (32-QFN) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8051MNL-EVAL | 功能描述:以太網開發工具 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ MII Support (32-QFN) - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8051MNLI | 功能描述:TXRX PHY 10/T100 3.3V 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| KSZ8051MNLI TR | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver with MII support (32-QFN, Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。