- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1161A (NXP Semiconductors N.V.) Full-speed Universal Serial Bus single-chip host and device controller PDF資料下載
參數資料
| 型號： | ISP1161A |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Full-speed Universal Serial Bus single-chip host and device controller |
| 中文描述： | 全速通用串行總線的單芯片主機和設備控制器 |
| 文件頁數： | 78/134頁 |
| 文件大?。?/td> | 587K |
| 代理商： | ISP1161A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁當前第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁
Philips Semiconductors
ISP1161A
Full-speed USB single-chip host and device controller
Product data
Rev. 03 — 23 December 2004
78 of 134
9397 750 13962
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
The SIE also checks for the device number and endpoint number and verifies
whether they are acceptable.
If the endpoint is enabled, the SIE checks the contents of the DcEndpointStatus
register. If the endpoint is empty, the data from USB is stored to FIFO during the
data phase, otherwise a NAK handshake is sent.
After the data phase, the SIE sends a handshake (ACK) to the host (except for ISO
endpoints).
The SIE updates the contents of the DcEndpointStatus register and the
DcInterrupt register, which in turn generates an interrupt to the microprocessor.
For ISO endpoints, the interrupt register is updated as soon as data is received
because there is no handshake phase.
On receiving interrupt, the microprocessor reads the DcInterrupt register. It will
know which endpoint has generated the interrupt and reads the content of the
corresponding DcEndpointStatus register. If the buffer is full, it empties the buffer,
so that data can be received by the SIE at the next OUT token phase.
11.2 Device DMA transfer
11.2.1
DMA for IN endpoint (internal DC to external USB host)
When the internal DMA handler is enabled and at least one buffer (Ping or Pong) is
free, the DREQ2 line is asserted. The external DMA controller then starts negotiating
for control of the bus. As soon as it has access, it asserts the DACK2 line and starts
writing data. The burst length is programmable. When the number of bytes equal to
the burst length has been written, the DREQ2 line is de-asserted. As a result, the
DMA controller de-asserts the DACK2 line and releases the bus. At that moment the
whole cycle restarts for the next burst.
When the buffer is full, the DREQ2 line will be de-asserted and the buffer is validated
(which means that it will be sent to the host when the next IN token comes in). When
the DMA transfer is terminated, the buffer is also validated (even if it is not full). A
DMA transfer is terminated when any of the following conditions are met:
the DMA count is complete
DMAEN = 0
the DMA controller asserts EOT.
11.2.2
DMA for OUT endpoint (external USB host to internal DC)
When the internal DMA handler is enabled and at least one buffer is full, the DREQ2
line is asserted. The external DMA controller then starts negotiating for control of the
bus, and as soon as it has access, it asserts the DACK2 line and starts reading the
data. The burst length is programmable. When the number of bytes equal to the burst
length has been read, the DREQ2 line is de-asserted. As a result, the DMA controller
de-asserts the DACK2 line and releases the bus. At that moment the whole cycle
restarts for the next burst. When all data are read, the DREQ2 line will be de-asserted
and the buffer is cleared (which means that it can be overwritten when a new packet
comes in).
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1161ABD | Full-speed Universal Serial Bus single-chip host and device controller |
| ISP1161ABM | Full-speed Universal Serial Bus single-chip host and device controller |
| ISP1161 | Full-speed Universal Serial Bus single-chip host and device controller |
| ISP1161A1 | Universal Serial Bus single-chip host and device controller |
| ISP1161A1BD | Universal Serial Bus single-chip host and device controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1161A1 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus single-chip host and device controller |
| ISP1161A1BD | 功能描述:IC USB HOST/DEVICE CTRLR 64-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| ISP1161A1BD,118 | 功能描述:USB 接口集成電路 USB1.1 HOST &DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1161A1BD,151 | 功能描述:USB 接口集成電路 USB1.1 HOST &DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1161A1BD,157 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。