參數資料
型號： ISL88550A
廠商： Intersil Corporation
英文描述： Synchronous Step Down Controller with Sourcing and Sinking LDO Regulator
中文描述： 同步降壓控制器，具有采購和下沉LDO穩壓器
文件頁數： 16/25頁
文件大?。?/td> 928K
代理商： ISL88550A
16
FN6168.0
October 12, 2005
drops 10% below or rises 10% above the nominal regulation
voltage, the ISL88550A pulls POK1 low. Any fault condition
forces POK1 low until the fault latch is cleared by toggling
SHDNA# or cycling AV
DD
power below 1V. For logic level
output voltages, connect an external pull up resistor between
POK1 and AV
DD
. A 100K resistor works well in most
applications. Note that the POK1 window detector is
completely independent of the overvoltage and undervoltage
protection fault detectors and the state of VTTS and VTTR.
SHDNA# and Output Discharge
The SHDNA# input corresponds to the Buck Regulator and
places the Buck Regulator’s portion of the IC in a low power
mode (see Electrical Characteristics Table). SHDNA# is also
used to reset a fault signal such as an overvoltage or
undervoltage fault.
When output discharge is enabled (OVP/UVP = AV
DD
or
open) and SHDNA# is pulled low, or if UVP is enabled
(OVP/UVP = AV
DD
) and V
OUT
falls to 70% of its regulation
set point, the ISL88550A discharges the Buck Regulator
output (via the OUT input) through an internal 15
switch to
ground. While the output is discharging, the PWM controller
is disabled, but the reference remains active to provide an
accurate threshold.
When output discharge is disabled (OVP/UVP = REF or
GND), the controller does not actively discharge the Buck
Output. Under these conditions, the Buck Output discharge
rate is determined by the load current and its output
capacitance. The Buck Regulator detects and latches the
discharge mode state set by OVP/UVP setting on startup.
STBY#
The STBY# input is an active low input that is used to
shutdown only the VTT output. When STBY# is low, VTT is
high impedance, but the VTTR output is still active if
SHDNA# is high. VTT and VTTR are pulled to 0V when
SHDNA is low.
Power OK (POK2)
POK2 is the open-drain output for a window comparator that
continuously monitors the VTTS input and VTTR output.
POK2 is high impedance as long as the output voltage is
within ±10% of the nominal regulation voltage as set by
REFIN. When V
VTTS
or V
VTTR
rise 10% above or 10%
below their nominal regulation voltage, the ISL88550A pulls
POK2 low. For logic level output voltages, connect an
external pull up resistor between POK2 and AV
DD
. A 100K
resistor works well in most applications. Note that the POK2
window detector is completely independent of the
overvoltage and undervoltage protection fault detectors and
the state of VDDQ.
Current Limit (LDO for VTT and VTTR buffer)
The VTT output is a linear regulator that regulates the input
(VTTI) to the V
REFIN
voltage. The feedback point for VTT
is at the VTTS input (see Figure 21 Block Diagram). VTT is
capable of sourcing up to 2.5A and sinking up to -2.0A
continuously. The current limit for VTT and VTTR is typically
+3.0A/-2.5A and ±40mA respectively. When the current limit
for either output is reached, the outputs regulate the current
not the voltage. The current limits for both VTT and VTTR
can be reduced from their full values by forcing the voltage at
the SS pin below 1.6V (typ), or by tying a resistor Rss
between the SS pin and ground such that 4μA*Rss is less
than 1.6V.
POK2 is pulled low when REFIN is < 0.8V.
Fault Protection
The ISL88550A provides overvoltage/undervoltage fault
protection in the buck controller. Select OVP/UVP to enable
and disable fault protection as shown in Table 3. Once
activated, the controller continuously monitors the output for
undervoltage and overvoltage fault conditions. Any VDDQ
shutdown due to OVP, UVP, OTP or SHDNA# = 0 should
also discharge VTT to 0V.
Overvoltage Protection (OVP)
When the output voltage rises above 114% of the nominal
regulation voltage and OVP is enabled (OVP/UVP = AV
DD
or open), the OVP circuit sets the fault latch, shuts down
the PWM controller, and immediately pulls UGATE low
and forces LGATE high. This turns on the synchronous
rectifier MOSFET with 100% duty cycle, rapidly
discharging the output capacitor and clamping the output
to ground. Note that immediately latching LGATE high can
cause the output voltage to go slightly negative due to
energy stored in the output LC circuit at the instant the
OVP occurs. If the load cannot tolerate a negative voltage,
place a power Schottky diode across the output to act as a
reverse polarity clamp. Toggle SHDNA# or cycle AV
DD
power below 1V to clear the fault latch and restart the
controller. OVP is disabled when OVP/UVP is connected
to REF or GND (see Table 3). OVP only applies to the
Buck Output. The VTT and VTTR Outputs do not have
overvoltage protection. When VDDQ is discharged to 0V
due to OVP, VTT is also discharged to 0V.
TABLE 2. SHUTDOWN AND STANDBY CONTROL LOGIC
SHDNA#
STBY#
BUCK
OUTPUT
VTT
VTTR
GND
X
OFF
OFF
(Discharge to
0V)
OFF
(Tracking
REFIN)
AV
DD
GND
ON
OFF
(High
Impedance)
ON
AV
DD
AV
DD
ON
ON
ON
ISL88550A
相關PDF資料
PDF描述
ISL88550AIRZ Synchronous Step Down Controller with Sourcing and Sinking LDO Regulator
ISL88550AIRZ-T Synchronous Step Down Controller with Sourcing and Sinking LDO Regulator
ISL88694 Octal Transparent D-Type Latches With 3-State Outputs 20-SOIC -40 to 85
ISL88694IH5 SMBus Accelerator (SMA)
ISL88694IH5-TK SMBus Accelerator (SMA)
相關代理商/技術參數
參數描述
ISL88550AEVAL1 功能描述:EVALUATION BOARD 1 ISL88550A RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
ISL88550AEVAL1Z 功能描述:EVALUATION BOARD 1 ISL88550A RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
ISL88550AIRZ 功能描述:電壓模式 PWM 控制器 INTEGRTD DDR PWR CNT RLR 2 8LD 5X5 TQFN RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
ISL88550AIRZ-T 功能描述:DC/DC 開關控制器 INTEGRTD DDR PWR CNT RLR 2 8LD 5X5 TQFN RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
ISL88550AIRZ-T7 功能描述:直流/直流開關轉換器 Integrated DDR Power Controller, 28LD 5x5 TQFN Pb-free, 1K O RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*