參數資料
型號： ISL5216KI
廠商： INTERSIL CORP
元件分類： 無繩電話/電話
英文描述： Four-Channel Programmable Digital DownConverter
中文描述： TELECOM, CELLULAR, BASEBAND CIRCUIT, PBGA196
封裝： 12 X 12 MM, 0.80 MM PITCH, PLASTIC, BGA-196
文件頁數： 37/65頁
文件大小： 1384K
代理商： ISL5216KI
37
TABLE 11. CARRIER NCO CENTER FREQUENCY UPDATE STROBE
REGISTER (IWA = *006h)
P(15:0)
FUNCTION
N/A
Writing to this address generates a strobe that transfers the CCF value to the active frequency register. The transfer to the active
register can also be done using the SYNCI pin to synchronize the transfer in multiple parts or to synchronize to an external event.
TABLE 12. TIMING NCO FREQUENCY CONTROL REGISTER, MSW (IWA = *007h)
P(31:0)
FUNCTION
31:0
These are the upper 32 bits of the 56-bit timing (resampler) NCO center frequency control.
TABLE 13. TIMING NCO FREQUENCY CONTROL REGISTER, LSW (IWA = *008h)
P(31:0)
FUNCTION
31:8
These are the lower 24 bits of the 56-bit timing (resampler) NCO center frequency control.
7:0
Unused, set to zero.
TABLE 14. TIMING NCO CENTER FREQUENCY LOAD STROBE REGISTER (IWA = *009h)
P(31:0)
FUNCTION
N/A
A write to this location will update the resampler NCO center frequency.
TABLE 15. FILTER COMPUTE ENGINE/RESAMPLER CONTROL REGISTER (IWA = *00Ah)
P(31:0)
FUNCTION
31
μ
PHold. When set, this bit stops the filter compute engine and allows the
μ
P access to the instruction and coefficient RAMs for
reading and writing. On the high to low transition, the filter compute engine is reset (the read and write pointers are reset and the
instruction at location 31 is fetched).
30
μ
PShiftZeroB. This bit, when set to zero, disables the coefficient shift bits (bits 9:8 of the master register when coefficient loading).
29
μ
PEN Limit. This bit disables the data path saturation logic. Provided for test. Active high. Set to 0 to disable the normal ROM
controlled limiting (ANDed with normal signal).
28:24
μ
PZ(4:0). These bits, when set to 0, zero the corresponding read pointer address bits. This allows the pointers to be aliased, i.e.,
multiple filters can access and/or modify the same pointer. They are provided to change filters, coefficients or decimation over a
sequence.
23
Unused, set to 0.
22
Timing (resampler) NCO ENsync. If this bit is set, the center frequency is updated on a SYNCI. Set to 1.
21:20
RSRVRS(1:0). Set to 01.
19
Beginning/End. This bit selects whether the resampler NCO is updated at the beginning of a FIR computation or at the end of each
FIR output computation. Usually, the resampler will be updated once at the beginning of each resampler computation and this will
be bit set to 1.
1
Once at the beginning of the FIR instruction.
0
At the last tap of each of the instruction’s FIR computations (once per output).
18
RSModeSelect. This bit selects whether the resampler is a phase shifter or a frequency shifter.
0
Phase shift. It uses the top
fi
ve bits of the timing NCO frequency to determine a phase shift and disables feedback in the timing
NCO phase accumulator—effect of the resampler is a constant phase shift.
1
Frequency shift. Effect of the resampler is a change in the sample rate.
17
RSCO. This bit is provided to force the resampler NCO carry when using the resampler as a phase shifter rather than for a frequency
shift. This bit must be set for phase shifting and cleared for frequency shifting. (The bit is Or-ed with the normal carry.)
16
RS NCO clear phase accumulator feedback on load. When this bit is set, the feedback in the resampler NCO phase accumulator is
zeroed whenever the center frequency word is updated. This forces the NCO to a known phase so the phase of multiple channels
can be aligned.
15
Force NCO load. This bit, when set, zeroes the feedback in the resampler NCO phase accumulator. This is provided for test or to
use the resampler for phase instead of frequency shifting.
ISL5216
相關PDF資料
PDF描述
ISL5216 Four-Channel Programmable Digital DownConverter
ISL5217EVAL1 Quad Programmable Up Converter
ISL5217KI Quad Programmable Up Converter
ISL5217 Quad Programmable Up Converter
ISL5217KIZ Quad Programmable Up Converter
相關代理商/技術參數
參數描述
ISL5216KI-1 功能描述:上下轉換器 QUAD DIGITAL DOWNCONVERTER,IND TEMP,1.OMM PITCH BGA PACKAG RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128
ISL5216KI-1Z 功能描述:上下轉換器 W/ANL QD DIG DWNCNVRTR 1 OM PITCH RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128
ISL5216KIZ 功能描述:上下轉換器 W/ANNEAL QD DIGTL DWNCNVRTR IND TEMP RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128
ISL5217 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Programmable Up Converter
ISL5217_05 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Programmable Up Converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*