- 您現在的位置：買賣IC網 > PDF目錄383133 > ISL5216KI (INTERSIL CORP) Four-Channel Programmable Digital DownConverter PDF資料下載
參數資料
| 型號： | ISL5216KI |
| 廠商： | INTERSIL CORP |
| 元件分類： | 無繩電話/電話 |
| 英文描述： | Four-Channel Programmable Digital DownConverter |
| 中文描述： | TELECOM, CELLULAR, BASEBAND CIRCUIT, PBGA196 |
| 封裝： | 12 X 12 MM, 0.80 MM PITCH, PLASTIC, BGA-196 |
| 文件頁數： | 11/65頁 |
| 文件大小： | 1384K |
| 代理商： | ISL5216KI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
11
ISL5216
clock and Q * (-SIN) and Q * COS on the second clock cycle.
The first integrator of the CIC is enabled on both clock cycles
to add the two products. The rest of the stages are enabled
only on the first cycle.
In complex input mode, the input level detector uses only I
samples for its magnitude computation.
The CIC decimation counter is programmed for two times
the number of complex input samples. The exponent input
must be the same for I and Q for the floating point modes.
See IWA *000h for details on controlling the complex input
mode.
NCO/Mixer
After the input select/format section, the samples are
multiplied by quadrature sine wave samples from the carrier
NCO. The NCO has a 32-bit frequency control, providing
sub-hertz resolution at the maximum clock rate. The
quadrature sinusoids have exceptional purity. The purity of
the NCO should not be the determining factor for the
receiver dynamic range performance. The phase
quantization to the sine/cosine generator is 24 bits and the
amplitude quantization is 19 bits.
The carrier NCO center frequency is loaded via the
The center frequency control is double buffered - the input
is loaded into a center frequency holding register via the
interface. The data is then transferred from the holding
register to the active register by a write to a address IWA
*006h or by a SYNCI signal, if loading via SYNCI is
enabled. To synchronize multiple channels, the carrier NCO
phase accumulator feedback can be zeroed on loading to
restart all of the NCOs at the same phase. A serial offset
frequency input is also available for each channel through
the D(15:0) parallel data input bus (if that bus is not needed
for data input). This is legacy support for HSP50210 type
tracking signals. See IWA=*000 and *004 for carrier offset
frequency parameters.
μ
P bus.
μ
P
After the mixers, a PN (pseudo noise) signal can be added to
the data. This feature is provided for test and to digitally
reduce the input sensitivity and adjust the receiver range
(sensitivity). The effect is the same as increasing the noise
figure of the receiver, reducing its sensitivity and overall
dynamic range. For testing, the PN generator provides a
wideband signal which may be used to verify the frequency
response of a filter. The one bit PN data is scaled by a 16-bit
programmable scale factor. The overall range for the PN is 0
to 1/4 full scale (see IWA = *001h). A gain of 0 disables the
PN input. The PN value is formed as:
where S is the sign extension of the 16 bit PN gain register
value (IWA = *001H) times the PN chip value and the 16 X’s
refer to the PN gain register times the PN chip value.
The minimum, non-zero, PN value is 2
(-108dBFS) on each axis (-105dBFS total). For an input noise
level of -75dBFS, this allows the SNR to be decreased in
steps of 1/8dB or less. The I and Q PN codes are offset in time
to decorrelate them. The PN code is selected and enabled in
the test control register (F800h). The PN is added to the signal
after the mix with the three sign bits aligned with the most
significant three bits of the signal, so the maximum level is -
12dBFS and the minimum, non-zero level is -108dBFS. The
PN code can be 2
-1, 2
-1 or 2
-18
of full scale
15
23
15
-1 * 2
23
-1.
CIC Filter
Next, the signal is filtered by a cascaded integrator/comb
(CIC) filter. A CIC filter is an efficient architecture for
decimation filtering. The power or magnitude squared
frequency response of the CIC filter is given by:
where
M = Number of delays (1 for the ISL5216)
N = Number of stages
and R = Decimation factor.
The passband frequency response for first (N=1) though fifth
(N=5) order CIC filters is plotted in Figure 13. The frequency
axis is normalized to f
S
/R, making f
sample rate. Figure 15 shows the frequency response for a
5
order filter but extends the frequency axis to f
(3 times the CIC output sample rate) to show alias rejection
for the out of band signals. Figure 14 uses information from
Figure 15 to provide the amplitude of the first (strongest)
alias as a function of the signal frequency or bandwidth from
DC. For example, with a 5
order CIC and f
(signal frequency is 1/8 the CIC output rate) Figure 14 shows
a first alias level of about -87 dB. Figure 14 is also listed in
table form in Table 51 (CIC Passband and Alias Levels).
S
/R = 1 the CIC output
th
S
/R = 3
th
S
/R = 0.125
The CIC filter order is programmable from 0 to 5. The CIC
may be bypassed by setting the CIC filter order to 0
(IWA = *004h bits 13:9 are all set equal to 1) and the CIC
barrel shift (IWA = *004h bits 19:14) to 45 decimal. The CIC
output rate must, however, be no more than CLK
where CLK
max
is the maximum clock frequency available on
the device (see electrical specifications section).
max
/ 4
The integrator bit widths are 69, 62, 53, 44, and 34 for the
first
through fifth stages, respectively, while the comb bit
widths are all 32. The integrators are sized for decimation
factors of up to 512 with five stages, 2048 with four stages,
32768 with three stages, and 65536 with one or two stages.
Higher decimations in the CIC should be avoided as they
will cause integrator overflow. In the ISL5216, the
t
PN VALUE
.
.
2
-3
2
-4
.
.
.
.
.
.
.
.
.
.
2
-17
2
-18
S S S
X
X
X X X X X X X X X X X X
X
X
P f
( )
π
f
R
)
-----------------------
----
sin
2N
=
相關PDF資料 |
PDF描述 |
|---|---|
| ISL5216 | Four-Channel Programmable Digital DownConverter |
| ISL5217EVAL1 | Quad Programmable Up Converter |
| ISL5217KI | Quad Programmable Up Converter |
| ISL5217 | Quad Programmable Up Converter |
| ISL5217KIZ | Quad Programmable Up Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL5216KI-1 | 功能描述:上下轉換器 QUAD DIGITAL DOWNCONVERTER,IND TEMP,1.OMM PITCH BGA PACKAG RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| ISL5216KI-1Z | 功能描述:上下轉換器 W/ANL QD DIG DWNCNVRTR 1 OM PITCH RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| ISL5216KIZ | 功能描述:上下轉換器 W/ANNEAL QD DIGTL DWNCNVRTR IND TEMP RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| ISL5217 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Programmable Up Converter |
| ISL5217_05 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Programmable Up Converter |
發布緊急采購，3分鐘左右您將得到回復。