- 您現在的位置：買賣IC網 > PDF目錄2080 > ISL24202IRTZ (Intersil)IC PROG 8BIT VCOM CALIBRTR 8TDFN PDF資料下載
參數資料
| 型號： | ISL24202IRTZ |
| 廠商： | Intersil |
| 文件頁數： | 12/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PROG 8BIT VCOM CALIBRTR 8TDFN |
| 標準包裝： | 100 |
| 類型： | 校準器 |
| 應用： | LCD 驅動器，基準電壓發生器 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WDFN 裸露焊盤 |
| 供應商設備封裝： | 8-TDFN（3x3） |
| 包裝： | 管件 |
ISL24202
9
FN7587.0
March 15, 2011
when not being driven. CE should be pulled low before powering
the device down to ensure that any glitches or transients during
power-down will not cause unwanted EEPROM overwriting.
The CE pin has a Schmitt trigger on the input to prevent false
triggering during slow transitions of the CE pin. The CE pin
transition time should be 10s or less.
Programming the EEPROM
To program the non-volatile EEPROM, pull the CTL pin above 4.9V
for more than 200s. The level and timing is shown in Figure 9. It
then takes a maximum of 100ms after CTL crosses 4.9V for the
programming to be completed inside the device.
When the part is programmed, the data in the counter register is
written into the EEPROM. This value will be loaded from the
EEPROM during subsequent power-ups as well as when the CE
pin is pulled low. The ISL24202 is factory-programmed to
mid-scale. As with asserting CE, the first pulse after a program
operation is ignored. The EEPROM contents can be written and
verified using the following steps:
1. Power-up the ISL24202. The EEPROM value will be loaded.
2. Set the CE pin to VDD.
3. Change the VOUT voltage using the CTL pin to the desired
value, noting that first pulse will be ignored.
4. Pull the CTL pin to 4.9V or higher for at least 200s. The
counter value will be written to EEPROM after 100ms.
5. Change the VOUT value (using the CTL pin) to a different value,
noting that first pulse after programming will be ignored.
6. Set the CE pin to 0V. The stored output value will be loaded
from EEPROM after 10ms.
7. Verify that the output value is the same value programmed in
Step 4.
The CTL pin should be left floating after programming. The
voltage at the CTL pin will be internally biased to VDD/2 to ensure
that no additional pulses will be seen by the Up/Down counter. To
prevent further changes, ground the CE pin.
Typical Application Circuit
Shown below in Figure 10 is a typical circuit that can be used to
program the ISL24202 via the up/down counter interface. Three
momentary push-button switches are required. SW1 connected
between CTL and AVDD allows the user to bring CTL above VDD for
programming the EEPROM, SW2 connected to VDD to pull CTL up,
and SW3 connected to GND to pull CTL to down. All the switches
should have 1kΩ current-limiting resistors in series.
For adjustment and programming to occur, the CE pin has to be
set to VDD. This can be achieved by a single-pull double-throw
switch (SW4) connected between VDD and GND.
Note that pressing the UP button increments the counter, but
results in VCOM_OUT decreasing. Similarly, pressing the DOWN
button decrements the counter, and results in VCOM_OUT
increasing.
CTL VOLTAGE
TIME
4.9V
tPROG
FIGURE 9. EEPROM PROGRAMMING
>200s
100ms
EEPROM
OPERATION
COMPLETE
FIGURE 10. TYPICAL APPLICATION CIRCUIT
ISL24202
CTL
0.01F
1k
VDD
CLOSE TO
UP
PROGRAM
1k
AVDD
DOWN
1k
EEPROM
CE
SET
R1
R2
RSET
OUT
VCOM to LCD Panel
SW2
SW1
SW3
SW4
AVDD
VDD
AVDD
GND
VDD
AVDD
0.01F
0.1F
ENABLE
VDD
ADJUST /
PROGRAM
DISABLE
EL5411T
相關PDF資料 |
PDF描述 |
|---|---|
| ISL24211IRTZ | IC VCOM CALIBRATOR I2C 10TDFN |
| ISL24212IRTZ | IC PROG 8BIT VCOM CALIBRTR 10TDF |
| ISL28197FRUZ-T7 | IC COMP RRIO SGL 800NA 6-TDFN |
| ISL3035EIRTZ-T | IC LEVEL TRANSLATOR 6CH 16-TQFN |
| ISL4089IBZ-T7A | IC VIDEO AMP DC-RESTORED 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL24202IRTZ-EVALZ | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Programmable VCOM Calibrator with EEPROM |
| ISL24202IRTZ-T13 | 功能描述:LCD Gamma緩沖器 ISL24202IRTZFREE VCM CLBTR W/AN I2C RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| ISL24211 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Programmable VCOM Calibrator with EEPROM and Output Buffer |
| ISL24211IRTZ | 功能描述:LCD Gamma緩沖器 ISL24211IRTZFREE VCO M DRVR + VCOM CLBTR RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| ISL24211IRTZ-EVALZ | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Programmable VCOM Calibrator with EEPROM and Output Buffer |
發布緊急采購，3分鐘左右您將得到回復。