參數資料
型號: ISD5116P
廠商: WINBOND ELECTRONICS CORP
元件分類: 音頻合成
英文描述: Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability
中文描述: 960 SEC, SPEECH SYNTHESIZER WITH RCDG, PDIP28
封裝: 0.600 INCH, PLASTIC, DIP-28
文件頁數: 17/57頁
文件大小: 735K
代理商: ISD5116P
October 2000
Page 16
The figure above shows the part of the ISD5116 block diagram that is used in Feed Through Mode. The
rest of the chip will be powered down to conserve power. The bold lines highlight the audio paths. Note
that the Microphone to ANA OUT +/– path is differential.
To select this mode, the following control bits must be configured in the ISD5116 configuration registers.
To set up the transmit path:
1. Select the FTHRU path through the ANA OUT MUX—Bits AOS0, AOS1 and AOS2 control the
state of the ANA OUT MUX. These are the D6, D7 and D8 bits respectively of Configuration
Register 0 (CFG0) and they should all be ZERO to select the FTHRU path.
2. Power up the ANA OUT amplifier—Bit AOPD controls the power up state of ANA OUT. This is bit
D5 of CFG0 and it should be a ZERO to power up the amplifier.
To set up the receive path:
1. Set up the ANA IN amplifier for the correct gain—Bits AIG0 and AIG1 control the gain settings of
this amplifier. These are bits D14 and D15 respectively of CFG0. The input level at this pin deter-
mines the setting of this gain stage. The
ANA IN Amplifier Gain Settings table
on page 25 will
help determine this setting. In this example, we will assume that the peak signal never goes
above 1 volt p-p single ended. That would enable us to use the 9 dB attenuation setting, or where
D14 is ONE and D15 is ZERO.
2. Power up the ANA IN amplifier—Bit AIPD controls the power up state of ANA IN. This is bit D13
of CFG0 and should be a ZERO to power up the amplifier.
3. Select the ANA IN path through the OUTPUT MUX—Bits OPS0 and OPS1 control the state of the
OUTPUT MUX. These are bits D3 and D4 respectively of CFG0 and they should be set to the
state where D3 is ONE and D4 is ZERO to select the ANA IN path.
4. Power up the Speaker Amplifier—Bits OPA0 and OPA1 control the state of the Speaker and AUX
amplifiers. These are bits D1 and D2 respectively of CFG0. They should be set to the state where
D1 is ONE and D2 is ZERO. This powers up the Speaker Amplifier and configures it for its higher
gain setting for use with a piezo speaker element and also powers down the AUX output stage.
The status of the rest of the functions in the ISD5116 chip must be defined before the configuration
registers settings are updated:
相關PDF資料
PDF描述
ISD5116S Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability
ISD5116SD Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability
ISD5116SI Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability
ISD5116X Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability
ISG510065 CATV OUT-OF-BAND TUNER
相關代理商/技術參數
參數描述
ISD5116PY 功能描述:IC VOICE REC/PLAY 8-16MN 28-DIP RoHS:是 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD5100 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP(0.300",7.62mm) 供應商設備封裝:28-PDIP 其它名稱:90-21300+000
ISD5116S 功能描述:IC VOICE REC/PLAY 8-16MN 28-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD5100 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP(0.300",7.62mm) 供應商設備封裝:28-PDIP 其它名稱:90-21300+000
ISD5116SD 制造商:WINBOND 制造商全稱:Winbond 功能描述:Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability
ISD5116SERIES 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single-Chip Voice Record/Playback Device with Digital Memory Capability
ISD5116SI 功能描述:IC VOICE REC/PL 8-16MN IN 28SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD5100 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP(0.300",7.62mm) 供應商設備封裝:28-PDIP 其它名稱:90-21300+000