- 您現在的位置：買賣IC網 > PDF目錄385399 > HT48C06 (Holtek Semiconductor Inc.) Cost-Effective I/O Type 8-Bit MCU PDF資料下載
參數資料
| 型號： | HT48C06 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | Cost-Effective I/O Type 8-Bit MCU |
| 中文描述： | 成本效益的I / O型8位微控制器 |
| 文件頁數： | 8/38頁 |
| 文件大?。?/td> | 264K |
| 代理商： | HT48C06 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
HT48R05A-1/HT48C05/HT48R06A-1/HT48C06
Rev. 1.10
8
June 9, 2004
The memory pointer register MP(01H) is a 7-bit register.
The bit 7 of MP is undefined and reading will return the
result 1 . Any writing operation to MP will only transfer
the lower 7-bit data to MP.
Accumulator
The accumulator is closely related to ALU operations. It
is also mapped to location 05H of the data memory and
can carry out immediate data operations. The data
movement between two data memory locations must
pass through the accumulator.
Arithmetic and Logic Unit
ALU
This circuit performs 8-bit arithmetic and logic opera-
tions. The ALU provides the following functions:
Arithmetic operations (ADD, ADC, SUB, SBC, DAA)
Logic operations (AND, OR, XOR, CPL)
Rotation (RL, RR, RLC, RRC)
Increment and Decrement (INC, DEC)
Branch decision (SZ, SNZ, SIZ, SDZ ....)
The ALU not only saves the results of a data operation
but also changes the status register.
Status Register
STATUS
This 8-bit register (0AH) contains the zero flag (Z), carry
flag (C), auxiliary carry flag (AC), overflow flag (OV),
power down flag (PDF), and watchdog time-out flag
(TO). It also records the status information and controls
the operation sequence.
With the exception of the TO and PDF flags, bits in the
status register can be altered by instructions like most
other registers. Any data written into the status register
will not change the TO or PDF flag. In addition opera-
tions related to the status register may give different re-
sults from those intended. The TO flag can be affected
only by system power-up, a WDT time-out or executing
the CLR WDT or HALT instruction. The PDF flag
can be affected only by executing the HALT or CLR
WDT instruction or a system power-up.
The Z, OV, AC and C flags generally reflect the status of
the latest operations.
In addition, on entering the interrupt sequence or exe-
cuting the subroutine call, the status register will not be
pushed onto the stack automatically. If the contents of
the status are important and if the subroutine can cor-
rupt the status register, precautions must be taken to
save it properly.
Interrupt
The device provides an external interrupt and internal
timer/event counter interrupts. The Interrupt Control
Register (INTC;0BH) contains the interrupt control bits
to set the enable or disable and the interrupt request
flags.
Once an interrupt subroutine is serviced, all the other in-
terrupts will be blocked (by clearing the EMI bit). This
scheme may prevent any further interrupt nesting. Other
interrupt requests may happen during this interval but
only the interrupt request flag is recorded. If a certain in-
terrupt requires servicing within the service routine, the
EMI bit and the corresponding bit of INTC may be set to
allow interrupt nesting. If the stack is full, the interrupt re-
quest will not be acknowledged, even if the related inter-
rupt is enabled, until the SP is decremented. If
immediate service is desired, the stack must be pre-
vented from becoming full.
All these kinds of interrupts have a wake-up capability.
As an interrupt is serviced, a control transfer occurs by
pushing the program counter onto the stack, followed by
a branch to a subroutine at specified location in the pro-
gram memory. Only the program counter is pushed onto
the stack. If the contents of the register or status register
/ % # % 0
" &
+ %
6 2
* $ % + 8
& % ( ' 0
" &
+ %
>
>
>
3 >
>
1 >
2 >
>
4 >
5 >
>
>
>
>
>
9 >
>
>
>
3 >
>
1 >
2 >
>
4 >
5 >
>
>
>
>
>
9 >
9 >
# , ' % ( $
, , % + + ' #
%
' + $ %
-
-
- >
A
# " + % ,
% , + B
B
3 9 >
>
>
RAM Mapping for HT48R06A-1/HT48C06
相關PDF資料 |
PDF描述 |
|---|---|
| HT48C10-1 | 8-Bit High Performance RISC-like Microcontroller Suitable for Multiple I/O Application(高性能、指令類似RISC的8位微控制器，用于多I/O接口設備) |
| HT48C50-1 | 8-Bit High Performance RISC-like Microcontroller Suitable for Multiple I/O Application(高性能、指令類似RISC的8位微控制器，用于多I/O接口設備) |
| HT48C50- | 8-BIT MICROCONTROLLER |
| HT48C70-1 | I/O Type 8-Bit MCU |
| HT48R70A-1 | I/O Type 8-Bit MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT48C062 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:八位高性能精簡指令集單片機，專為經濟型多輸入輸出控制的產品設計 |
| HT48C062_08 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Cost-Effective I/O Type 8-Bit MCU |
| HT48C10 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit Microcontroller Series |
| HT48C10(18DIP-F) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| HT48C10(20DIP-F) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。