- 您現在的位置：買賣IC網 > PDF目錄385399 > HT46R221 (Holtek Semiconductor Inc.) 8-Bit A/D Type MCU PDF資料下載
參數資料
| 型號： | HT46R221 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 8-Bit A/D Type MCU |
| 中文描述： | 8位A / D型微控制器 |
| 文件頁數： | 22/46頁 |
| 文件大?。?/td> | 390K |
| 代理商： | HT46R221 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
HT46R22/HT46C22
Rev. 1.10
22
October 2, 2002
SRW bit
The SRW bit means that the master device wants to
read from or write to the I
2
C BUS. The slave device
check this bit to understand itself if it is a transmitter or a
receiver. The SRW bit is set to 1 means that the mas-
terwantstoreaddatafromtheI
2
CBUS,sotheslavede-
vice must write data to a bus as a transmitter. The SRW
is cleared to 0 means that the master wants to write
data to the I
2
C BUS, so the slave
device must read data from the I
2
C BUS as a receiver.
Acknowledge bit
Oneoftheslavedevicegeneratesanacknowledgesignal,
when the slave address is matched. The master device
can check this acknowledge bit to know if the slave device
accepts the calling address. If no acknowledge bit, the
mastermustsendaSTOPbitandendthecommunication.
When the I
2
C BUS status register bit 6 HAAS is high, it
means the address is matched, so the slave must check
SRW as a transmitter (set HTX) to 1 or as a receiver
(clear HTX) to 0 .
Data byte
The data is 8 bits and is sent after the slave device has
acknowledges the slave address. The first bit is MSB
and the 8th bit is LSB. The receiver sends the acknowl-
edge signal ( 0 ) and continues to receive the next 1
byte data. If the transmitter checks and there s no ac-
knowledge signal, then it release the SDA line, and the
master sends a STOP signal to release the I
2
C BUS.
The data is stored in the HDR register. The transmitter
must write data to the HDR before transmit data and the
receiver must read data from the HDR after receiving
data.
Receive acknowledge bit
When the receiver wants to continue to receive the next
data byte, it generates an acknowledge bit (TXAK) at
the 9th clock. The transmitter checks the acknowledge
bit (RXAK) to continue to write data to the I
2
C BUS or
change to receive mode and dummy read the HDR reg-
ister to release the SDA line and the master sends the
STOP signal.
Stop bit
Start bit
( ( > * (
(
( > !
(
! ! # A
- ' $
( # ) > * (
Data stable and data allow change
相關PDF資料 |
PDF描述 |
|---|---|
| HT46C23 | A/D Type 8-Bit MCU |
| HT46C24 | A/D Type 8-Bit MCU |
| HT46R24 | A/D Type 8-Bit MCU |
| HT46C46 | Cost-Effective A/D Type 8-Bit MCU |
| HT46C47 | Cost-Effective A/D Type 8-Bit MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT46R23 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit OTP Microcontroller |
| HT46R232 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D Type 8-Bit MCU |
| HT46R24 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D Type 8-Bit MCU |
| HT46R24_06 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D Type 8-Bit MCU |
| HT46R32 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D Type 8-Bit OTP MCU with OPA |
發布緊急采購，3分鐘左右您將得到回復。