- 您現在的位置：買賣IC網 > PDF目錄385399 > HT46R221 (Holtek Semiconductor Inc.) 8-Bit A/D Type MCU PDF資料下載
參數資料
| 型號： | HT46R221 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 8-Bit A/D Type MCU |
| 中文描述： | 8位A / D型微控制器 |
| 文件頁數： | 21/46頁 |
| 文件大小： | 390K |
| 代理商： | HT46R221 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
HT46R22/HT46C22
Rev. 1.10
21
October 2, 2002
3: Set EHI bit of the interrupt control register 1 (INTC1)
bit 0 to enable the I
2
C BUS interrupt.
Label
(HSR)
Bits
Function
HCF
7
HCFisclearto 0 whenonedatabyteis
being transferred, HCF is set to 1 indi-
cating 8-bit data communication has
been finished.
HAAS
6
HAAS is set to 1 when the calling ad-
dressed is matched, and I
2
C BUS inter-
rupt will occur and HIF is set.
HBB
5
HBB is set to 1 when I
2
C BUS is busy
and HBB is cleared to 0 means that
the I
2
C BUS is not busy.
4
Unused bit, read as 0
3
Unused bit, read as 0
SRW
2
SRW is set to
wants to read data from the I
2
C BUS, so
the slave must transmit data to the mas-
ter. SRW is cleared to
master wants to write data to the I
2
C
BUS, so the slave must receive data
from the master.
1
when the master
0
when the
1
Unused bit, read as 0
RXAK
0
RXAK is cleared to 0 when the master
receives an 8-bit data and acknowledg-
ment at the 9th clock, RXAK is set to 1
means not acknowledged.
HSR register
Start signal
The START signal is generated only by the master de-
vice. The other device in the bus must detect the START
signal to set the I
2
C BUS busy bit (HBB). The START
signal is SDA line from high to low, when SCL is high.
Slave address
The master must select a device for transferring the
data by sending the slave device address after the
START signal. All device in the I
2
C BUS will receive the
I
2
C BUS slave address (7 bits) to compare with its own
slave address (7 bits). If the slave address is matched,
the slave device will generate an interrupt and save the
following bit (8th bit) to SRW bit and sends an acknowl-
edge bit (low level) to the 9th bit. The slave device also
sets the status flag (HAAS), when the slave address is
matched.
In interrupt subroutine, check HAAS bit to know whether
theI
2
CBUSinterruptcomesfromaslaveaddressthatis
matched or a data byte transfer is completed. When the
slave address is matched, the device must be in trans-
mit mode or receive mode and write data to HDR or
dummy read from HDR to release the SCL line.
!
"
#
$
%
& ' #
$
(
(
Slave address
相關PDF資料 |
PDF描述 |
|---|---|
| HT46C23 | A/D Type 8-Bit MCU |
| HT46C24 | A/D Type 8-Bit MCU |
| HT46R24 | A/D Type 8-Bit MCU |
| HT46C46 | Cost-Effective A/D Type 8-Bit MCU |
| HT46C47 | Cost-Effective A/D Type 8-Bit MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT46R23 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit OTP Microcontroller |
| HT46R232 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D Type 8-Bit MCU |
| HT46R24 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D Type 8-Bit MCU |
| HT46R24_06 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D Type 8-Bit MCU |
| HT46R32 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D Type 8-Bit OTP MCU with OPA |
發布緊急采購，3分鐘左右您將得到回復。