- 您現在的位置：買賣IC網 > PDF目錄384404 > HGT1N30N60A4D (FAIRCHILD SEMICONDUCTOR CORP) 600V, SMPS Series N-Channel IGBT with Anti-Parallel Hyperfast Diode PDF資料下載
參數資料
| 型號： | HGT1N30N60A4D |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 功率晶體管 |
| 英文描述： | 600V, SMPS Series N-Channel IGBT with Anti-Parallel Hyperfast Diode |
| 中文描述： | 96 A, 600 V, N-CHANNEL IGBT |
| 封裝： | ISOTOP-4 |
| 文件頁數： | 8/9頁 |
| 文件大小： | 144K |
| 代理商： | HGT1N30N60A4D |
2001 Fairchild Semiconductor Corporation
HGT1N30N60A4D Rev. B
Handling Precautions for IGBTs
Insulated Gate Bipolar Transistors are susceptible to gate-
insulation damage by the electrostatic discharge of energy
through the devices. When handling these devices, care
should be exercised to assure that the static charge built in
the handler’s body capacitance is not discharged through the
device. With proper handling and application procedures,
however, IGBTs are currently being extensively used in
production by numerous equipment manufacturers in
military, industrial and consumer applications, with virtually
no damage problems due to electrostatic discharge. IGBTs
can be handled safely if the following basic precautions are
taken:
1. Prior to assembly into a circuit, all leads should be kept
shorted together either by the use of metal shorting
springs or by the insertion into conductive material such
as “ECCOSORBD LD26” or equivalent.
2. When devices are removed by hand from their carriers,
the hand being used should be grounded by any suitable
means - for example, with a metallic wristband.
3. Tips of soldering irons should be grounded.
4. Devices should never be inserted into or removed from
circuits with power on.
5.
Gate Voltage Rating
- Never exceed the gate-voltage
rating of V
GEM
. Exceeding the rated V
GE
can result in
permanent damage to the oxide layer in the gate region.
6.
Gate Termination
- The gates of these devices are
essentially capacitors. Circuits that leave the gate
open-circuited or floating should be avoided. These
conditions can result in turn-on of the device due to
voltage buildup on the input capacitor due to leakage
currents or pickup.
7.
Gate Protection
- These devices do not have an internal
monolithic Zener diode from gate to emitter. If gate
protection is required an external Zener is recommended.
Operating Frequency Information
Operating frequency information for a typical device
(Figure 3) is presented as a guide for estimating device
performance for a specific application. Other typical
frequency vs collector current (I
CE
) plots are possible using
the information shown for a typical unit in Figures 5, 6, 7, 8, 9
and 11. The operating frequency plot (Figure 3) of a typical
device shows f
MAX1
or f
MAX2
; whichever is smaller at each
point. The information is based on measurements of a
typical device and is bounded by the maximum rated
junction temperature.
f
MAX1
is defined by f
MAX1
= 0.05/(t
d(OFF)I
+ t
d(ON)I
).
Deadtime (the denominator) has been arbitrarily held to 10%
of the on-state time for a 50% duty factor. Other definitions
are possible. t
d(OFF)I
and t
d(ON)I
are defined in Figure 25.
Device turn-off delay can establish an additional frequency
limiting condition for an application other than T
JM
. t
d(OFF)I
is important when controlling output ripple under a lightly
loaded condition.
f
MAX2
is defined by f
MAX2
= (P
D
- P
C
)/(E
OFF
+ E
ON2
). The
allowable dissipation (P
D
) is defined by P
D
= (T
JM
- T
C
)/R
θ
JC
.
The sum of device switching and conduction losses must
not exceed P
D
. A 50% duty factor was used (Figure 3) and
the conduction losses (P
C
) are approximated by
P
C
= (V
CE
x I
CE
)/2.
E
ON2
and E
OFF
are defined in the switching waveforms
shown in Figure 25. E
ON2
is the integral of the instantaneous
power loss (I
CE
x V
CE
) during turn-on and E
OFF
is the
integral of the instantaneous power loss (I
CE
x V
CE
) during
turn-off. All tail losses are included in the calculation for
E
OFF
; i.e., the collector current equals zero (I
CE
= 0).
HGT1N30N60A4D
相關PDF資料 |
PDF描述 |
|---|---|
| HGT1N40N60A4 | 600V, SMPS Series N-Channel IGBT with Anti-Parallel Hyperfast Diode |
| HGT1N40N60A4D | 600V, SMPS Series N-Channel IGBT with Anti-Parallel Hyperfast Diode |
| HGT1S10N120BNS | 35A, 1200V, NPT Series N-Channel IGBT(35A, 1200V,NPT系列N溝道絕緣柵雙極型晶體管) |
| HGTP10N120BN | 35A, 1200V, NPT Series N-Channel IGBT |
| HGTP10N120BN | 35A, 1200V, NPT Series N-Channel IGBT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HGT1N40N60A4 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:600V, SMPS Series N-Channel IGBT with Anti-Parallel Hyperfast Diode |
| HGT1N40N60A4D | 功能描述:IGBT 晶體管 45A 600V N-Ch RoHS:否 制造商:Fairchild Semiconductor 配置: 集電極—發射極最大電壓 VCEO:650 V 集電極—射極飽和電壓:2.3 V 柵極/發射極最大電壓:20 V 在25 C的連續集電極電流:150 A 柵極—射極漏泄電流:400 nA 功率耗散:187 W 最大工作溫度: 封裝 / 箱體:TO-247 封裝:Tube |
| HGT1S020N35G3VL | 制造商:Harris Corporation 功能描述: |
| HGT1S10N120BNS | 功能描述:IGBT 晶體管 35A 1200V NPT N-Ch RoHS:否 制造商:Fairchild Semiconductor 配置: 集電極—發射極最大電壓 VCEO:650 V 集電極—射極飽和電壓:2.3 V 柵極/發射極最大電壓:20 V 在25 C的連續集電極電流:150 A 柵極—射極漏泄電流:400 nA 功率耗散:187 W 最大工作溫度: 封裝 / 箱體:TO-247 封裝:Tube |
| HGT1S10N120BNS9A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | IGBT | N-CHAN | 1.2KV V(BR)CES | 17A I(C) | TO-263AB |
發布緊急采購，3分鐘左右您將得到回復。