- 您現在的位置：買賣IC網 > PDF目錄370251 > FTS64K (飛思卡爾半導體(中國)有限公司) 50/MDR/RECP/VERT PRS FIT/M2.6/SCW/30 MIN PDF資料下載
參數資料
| 型號： | FTS64K |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | 50/MDR/RECP/VERT PRS FIT/M2.6/SCW/30 MIN |
| 中文描述： | 64K的快閃記憶體字節 |
| 文件頁數： | 32/44頁 |
| 文件大?。?/td> | 401K |
| 代理商： | FTS64K |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
FTS64K Block User Guide — Version V01.00
32
4.1.2 Program and Erase Sequences in User Mode
A Command State Machine is used to supervise the write sequencing for program and erase. The
erase-verify command follows the same flow. Before starting a command sequence, it is necessary to
verify that there is no pending access error or protection violation (the ACCERR and PVIOL flags should
beclearedintheFSTATregister)ItisthenrequiredtosetthePPAGEregister.Theprocedureisasfollows:
1.
Verify that all ACCERR and PVIOL flags in the FSTAT register are cleared.
2.
Write to the core PPAGE register ($x030) to select one of the pages to be programmed if
programming in the $8000-$BFFF address range. There is no need to set PPAGE when
programming in the $4000-$7FFF or $C000-$FFFF address ranges.
After this possible initialization step the CBEIF flag should be tested to ensure that the address, data and
command buffers are empty. If so, the program/erase command write sequence can be started. The
following 3-step command write sequence must be strictly adhered to and no intermediate writes to the
Flash module are permitted between the 3 steps. It is possible to read any Flash register during a command
sequence. The command sequence is as follows:
1.
Write the aligned data word to be programmed to the valid Flash address space. The address and
data will be stored in internal buffers. For program, all address bits are valid. For erase, the value
of the data bytes is don’t care. For mass erase, the address can be anywhere in the available address
space of the block to be erased. For sector erase the address bits[8:0] are ignored.
Write the program or erase command to the command buffer. These commands are listed in
Table
4-1
.
2.
3.
CleartheCBEIFflagbywritinga“1”toittolaunchthecommand.WhentheCBEIFflagiscleared,
the CCIF flag is cleared by hardware indicating that the command was successfully launched. The
CBEIF flag will be set again indicating the address, data and command buffers are ready for a new
command sequence to begin.
The completion of the command is indicated by the CCIF flag setting. The CCIF flag only sets when all
active and pending commands have been completed.
NOTE
The Command State Machine will flag errors in program or erase write sequences by means of the
ACCERR (access error) and PVIOL (protection violation) flags in the FSTAT register. An erroneous
command write sequence will abort and set the appropriate flag. If set, the user must clear the ACCERR
or PVIOL flags before commencing another command write sequence. By writing a 0 to the CBEIF flag
the command sequence can be aborted after the word write to the Flash address space or after writing a
command to the FCMD register and before the command is launched. Writing a “0” to the CBEIF flag in
this way will set the ACCERR flag.
A summary of the program algorithm is shown in
Figure 4-2
. For the erase algorithm, the user writes
either a mass or sector erase command to the FCMD register.
F
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| FTT1010-M | Frame Transfer CCD Image Sensor |
| FTT1010M | Frame Transfer CCD Image Sensor |
| FU-675PDF-V1M25A | Optoelectronic |
| FU-675PDF-V1M26A | Optoelectronic |
| FU-675PDF-V1M27A | Optoelectronic |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FTS900 | 制造商:Fluke Networks 功能描述:FIBER QUICKMAP WITH VFL 制造商:Fluke Networks 功能描述:FIBER QUICKMAP KIT; Kit Contents:Fibre QuickMap, SC/ LC Hybrid Test Reference Cords, VisiFault VFL; Primary Product 1:Fibre QuickMap; Primary Product 2:SC/LC Test Reference Cord; Primary Product 3:VisiFault VFL ;RoHS Compliant: NA |
| FTSC421502459 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| FT-SFM2 | 制造商:Panasonic Electric Works 功能描述:THRU-BEAM TYPE FIBER 制造商:Panasonic Electric Works 功能描述:OPTO SENSORN FT-SNFM2 |
| FT-SFM2L | 制造商:Panasonic Electric Works 功能描述:FIBER SENSOR2.5MM DIA. THRU. W/ LENS LO 制造商:Panasonic Electric Works 功能描述:THRU-BEAM TYPE FIBER |
| FT-SFM2SV2 | 制造商:Panasonic Electric Works 功能描述:FIBER SENSOR2.5MM DIA. THRU. W/ 1.5MM 制造商:Panasonic Electric Works 功能描述:SENSOR, FIBRE OPTIC, THRUBEAM, 550MM; Fiber Optic Sensor Type:Thrubeam ;RoHS Compliant: Yes 制造商:Panasonic Electric Works 功能描述:THRU-BEAM TYPE FIBER |
發布緊急采購，3分鐘左右您將得到回復。