- 您現在的位置：買賣IC網 > PDF目錄375796 > FGK60N6S2D (FAIRCHILD SEMICONDUCTOR CORP) INDUSTRIAL POWER SUPPLY, 85-265VAC/120-330VDC INPUT, 24V@14A RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | FGK60N6S2D |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | IGBT 晶體管 |
| 英文描述： | INDUSTRIAL POWER SUPPLY, 85-265VAC/120-330VDC INPUT, 24V@14A RoHS Compliant: Yes |
| 中文描述： | 75 A, 600 V, N-CHANNEL IGBT |
| 封裝： | PLASTIC, STRETCH TO-247, 3 PIN |
| 文件頁數： | 8/9頁 |
| 文件大?。?/td> | 185K |
| 代理商： | FGK60N6S2D |
2002 Fairchild Semiconductor Corporation
FGK60N6S2D Rev. A1
F
Handling Precautions for IGBTs
Insulated Gate Bipolar Transistors are susceptible to
gate-insulation damage by the electrostatic
discharge of energy through the devices. When
handling these devices, care should be exercised to
assure that the static charge built in the handler
’
s
body capacitance is not discharged through the
device. With proper handling and application
procedures, however, IGBTs are currently being
extensively used in production by numerous
equipment manufacturers in military, industrial and
consumer applications, with virtually no damage
problems due to electrostatic discharge. IGBTs can
be handled safely if the following basic precautions
are taken:
1. Prior to assembly into a circuit, all leads should be
kept shorted together either by the use of metal
shorting springs or by the insertion into conduc-
tive material such as
“
ECCOSORBD
LD26
”
or
equivalent.
2. When devices are removed by hand from their
carriers, the hand being used should be
grounded by any suitable means - for example,
with a metallic wristband.
3. Tips of soldering irons should be grounded.
4. Devices should never be inserted into or removed
from circuits with power on.
5.
Gate Voltage Rating
- Never exceed the gate-
voltage rating of V
. Exceeding the rated V
GE
can result in permanent damage to the oxide
layer in the gate region.
6.
Gate Termination
- The gates of these devices
are essentially capacitors. Circuits that leave the
gate open-circuited or floating should be avoided.
These conditions can result in turn-on of the
device due to voltage buildup on the input
capacitor due to leakage currents or pickup.
7.
Gate Protection
- These devices do not have an
internal monolithic Zener diode from gate to
emitter. If gate protection is required an external
Zener is recommended.
Operating Frequency Information
Operating frequency information for a typical device
(Figure 3) is presented as a guide for estimating
device performance for a specific application. Other
typical frequency vs collector current (I
) plots are
possible using the information shown for a typical
unit in Figures 5, 6, 7, 8, 9 and 11. The operating
frequency plot (Figure 3) of a typical device shows
f
MAX1
or f
MAX2
; whichever is smaller at each point.
The information is based on measurements of a
typical device and is bounded by the maximum rated
junction temperature.
f
is defined by f
= 0.05/(t
+ t
).
Deadtime (the denominator) has been arbitrarily held
to 10% of the on-state time for a 50% duty factor.
Other definitions are possible. t
d(OFF)I
and t
d(ON)I
are
defined in Figure 27. Device turn-off delay can
establish an additional frequency limiting condition
for an application other than T
. t
is important
when controlling output ripple under a lightly loaded
condition.
f
MAX2
is defined by f
MAX2
= (P
D
- P
C
)/(E
OFF
+ E
ON2
).
The allowable dissipation (P
D
) is defined by
P
D
= (T
JM
- T
C
)/R
θ
JC
. The sum of device switching
and conduction losses must not exceed P
D
. A 50%
duty factor was used (Figure 3) and the conduction
losses (P
C
) are approximated by P
C
= (V
CE
x I
CE
)/
2.
E
and E
are defined in the switching
waveforms shown in Figure 27. E
ON2
is the integral
of the instantaneous power loss (I
CE
x V
CE
) during
turn-on and E
OFF
is the integral of the instantaneous
power loss (I
CE
x V
CE
) during turn-off. All tail losses
are included in the calculation for E
; i.e., the
collector current equals zero (I
CE
= 0)
ECCOSORBD
is a Trademark of Emerson and Cumming, Inc.
相關PDF資料 |
PDF描述 |
|---|---|
| FGL40N120AND | 1200V NPT IGBT |
| FGL40N150 | Electrical Characteristics of the IGBT |
| FGL40N150D | Electrical Characteristics of the IGBT |
| FGL60N100BNTD | NPT-Trench IGBT |
| FGL60N100D | Electrical Characteristics of IGBT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FGKBK | 功能描述:按鈕開關 Pushbutton RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0 |
| FGKBLK | 功能描述:按鈕開關 Pushbutton RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0 |
| FGKGN | 功能描述:按鈕開關 Pushbutton RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0 |
| FGKRD | 功能描述:按鈕開關 Pushbutton RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0 |
| FGL.0K.110.CZZ | 功能描述:環形推拉式連接器 STRAIGHT PLUG FEMALE W. CABLE COLLET RoHS:否 制造商:Hirose Connector 產品類型:Connectors 系列:HR10 觸點類型:Socket (Female) 外殼類型:Receptacle 觸點數量:4 外殼大小:7 安裝風格:Panel 端接類型:Solder 電流額定值:2 A |
發布緊急采購，3分鐘左右您將得到回復。