參數資料
型號： EVAL-ADV7180-32EBZ
廠商： Analog Devices Inc
文件頁數： 60/116頁
文件大小： 0K
描述： BOARD EVAL FOR ADV7180
標準包裝： 1
系列： Advantiv®
主要目的： 視頻，SDTV 視頻解碼器 - NTSC，PAL，SECAM
嵌入式： 否
已用 IC / 零件： ADV7180
主要屬性： CVBS（復合），Y/C（S 視頻）和 YPrPb（元件）輸入
次要屬性： 8 位 ITU-R BT.656 YCrCb 4:2:2 輸出
已供物品： 板
ADV7180
Data Sheet
Rev. I | Page 48 of 116
VS and FIELD Configuration
The following controls allow the user to configure the behavior
of the VS and FIELD output pins, as well as the generation of
embedded AV codes.
The 64-lead LQFP has separate VS and FIELD pins. The 48-lead
LQFP, 40-lead LFCSP, and 32-lead LFCSP do not have separate
VS and FIELD pins but can output either VS or FIELD on Pin 45
(48-lead LQFP), Pin 37 (40-lead LFCSP), or Pin 31 (32-lead
LFCSP), which is the VS/FIELD pin.
SQPE, Square Pixel Mode, Address 0x01[2]
The SQPE bit allows the user to select the square pixel mode.
This mode is not suitable for poor time-based video sources.
This mode is recommended for professional applications only
and should not be used with VCR or tuner sources.
Setting SQPE to 1 enables square pixel mode. The LLC for
NTSC is 24.5454 MHz and 29.5 MHz for PAL. The crystal
frequency does not change.
VS/FIELD, Address 0x58[0]
This feature is used for the 48-lead LQFP, 40-lead LFCSP, and
32-lead LFCSP only. The polarity of this bit determines what
signal appears on the VS/FIELD pin.
When this bit is set to 0 (default), the FIELD signal is output.
When this bit is set to 1, the VSYNC signal is output.
The 64-lead LQFP has dedicated FIELD and VSYNC pins.
ADV encoder-compatible signals via the NEWAVMODE
register follow:
PVS, PF
HVSTIM
VSBHO, VSBHE
VSEHO, VSEHE
For NTSC control,
NVBEGDELO, NVBEGDELE, NVBEGSIGN, NVBEG[4:0]
NVENDDELO, NVENDDELE, NVENDSIGN, NVEND[4:0]
NFTOGDELO, NFTOGDELE, NFTOGSIGN, NFTOG[4:0]
For PAL control,
PVBEGDELO, PVBEGDELE, PVBEGSIGN, PVBEG[4:0]
PVENDDELO, PVENDDELE, PVENDSIGN, PVEND[4:0]
PFTOGDELO, PFTOGDELE, PFTOGSIGN, PFTOG[4:0]
NEWAVMODE, New AV Mode, Address 0x31[4]
When NEWAVMODE is 0, EAV/SAV codes are generated to
suit Analog Devices encoders. No adjustments are possible.
Setting NEWAVMODE to 1 (default) enables the manual position
of the VSYNC, FIELD, and AV codes using Register 0x32 to
Register 0x33 and Register 0xE5 to Register 0xEA. Default register
settings are CCIR656 compliant; see Figure 38 for NTSC and
Figure 43 for PAL. For recommended manual user settings, see
HVSTIM, Horizontal VS Timing, Address 0x31[3]
The HVSTIM bit allows the user to select where the VS signal is
asserted within a line of video. Some interface circuitry may require
VS to go low while HS is low.
When HVSTIM is 0 (default), the start of the line is relative to HSE.
When HVSTIM is 1, the start of the line is relative to HSB.
VSBHO, VS Begin Horizontal Position Odd, Address 0x32[7]
The VSBHO and VSBHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high or low.
When VSBHO is 0 (default), the VS pin goes high in the middle
of a line of video (odd field).
When VSBHO is 1, the VS pin changes state at the start of a line
(odd field).
VSBHE, VS Begin Horizontal Position Even, Address 0x32[6]
The VSBHO and VSBHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to only change state
when HS is high or low.
When VSBHE is 0 (default), the VS pin goes high in the middle
of a line of video (even field).
When VSBHE is 1, the VS pin changes state at the start of a line
(even field).
VSEHO, VS End Horizontal Position Odd, Address 0x33[7]
The VSEHO and VSEHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high or low.
When VSEHO is 0 (default), the VS pin goes low (inactive) in
the middle of a line of video (odd field).
When VSEHO is 1, the VS pin changes state at the start of a line
(odd field).
VSEHE, VS End Horizontal Position Even, Address 0x33[6]
The VSEHO and VSEHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high or low.
When VSEHE is 0 (default), the VS pin goes low (inactive) in
the middle of a line of video (even field).
When VSEHE is 1, the VS pin changes state at the start of a line
(even field).
PVS, Polarity VS, Address 0x37[5]
The polarity of the VS pin can be inverted using the PVS bit.
When PVS is 0 (default), VS is active high.
When PVS is 1, VS is active low.
相關PDF資料
PDF描述
M1DXK-2436J IDC CABLE - MKR24K/MC24G/X
AD818AR-EBZ BOARD EVAL FOR AD818AR
5504970-2 CABLE ASSEM FIBER SC-SC 2 METER
AD817AR-EBZ BOARD EVAL FOR AD817AR
AD813AR-14-EBZ BOARD EVAL FOR AD813AR-14
相關代理商/技術參數
參數描述
EVAL-ADV7180-48EBZ 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 4?? Oversampling SDTV Video Decoder
EVAL-ADV7180-48EBZ-8P-CAL 制造商:Analog Devices 功能描述:
EVAL-ADV7180LFEB 制造商:Analog Devices 功能描述:ADV7180 EVAL BOARD - Bulk
EVAL-ADV7180LFEBZ 功能描述:BOARD EVAL FOR ADV7180 LFCSP RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:Advantiv® 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源
EVAL-ADV7180LQEBZ 功能描述:BOARD EVALUATION ADV7180 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:Advantiv® 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*