- 您現在的位置：買賣IC網 > PDF目錄16565 > EVAL-ADF4360-9EBZ1 (Analog Devices Inc)EVALUATION BOARD FOR ADF4360-9 PDF資料下載
參數資料
| 型號： | EVAL-ADF4360-9EBZ1 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVALUATION BOARD FOR ADF4360-9 |
| 標準包裝： | 1 |
| 主要目的： | 計時，頻率合成器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ADF4360-9 |
| 主要屬性： | 帶 VCO 的單路整數-N PLL |
| 次要屬性： | 360MHz，1.6MHz PFD |
| 已供物品： | 板 |
| 其它名稱： | Q5254840 |
Data Sheet
ADF4360-9
Rev. C | Page 17 of 24
POWER-UP
Power-Up Sequence
The correct programming sequence for the ADF4360-9 after
power-up is as follows:
1. R Counter Latch
2. Control Latch
3. N Counter Latch
Initial Power-Up
Initial power-up refers to programming the part after the
application of voltage to the AVDD, DVDD, and VVCO pins. On
initial power-up, an interval is required between programming
the control latch and programming the N counter latch. This
interval is necessary to allow the transient behavior of the
ADF4360-9 during initial power-up to settle.
During initial power-up, a write to the control latch powers up
the part, and the bias currents of the VCO begin to settle. If
these currents have not settled to within 10% of their steady-
state value, and if the N counter latch is then programmed, the
VCO may not oscillate at the desired frequency, which does not
allow the band select logic to choose the correct frequency
band, and the ADF4360-9 may not achieve lock. If the
recommended interval is inserted, and the N counter latch is
programmed, the band select logic can choose the correct
frequency band, and the part locks to the correct frequency.
The duration of this interval is affected by the value of the
capacitor on the CN pin (Pin 14). This capacitor is used to
reduce the close-in noise of the ADF4360-9 VCO. The
recommended value of this capacitor is 10 F. Using this
value requires an interval of ≥15 ms between the latching in
of the control latch bits and latching in of the N counter latch
bits. If a shorter delay is required, the capacitor can be reduced.
A slight phase noise penalty is incurred by this change, which is
further explained in Table 6.
Table 6. CN Capacitance vs. Interval and Phase Noise
CN Value
Recommended Interval Between
Control Latch and N Counter Latch
Open-Loop Phase Noise @ 10 kHz Offset
L1 and L2 = 18.0 nH
L1 and L2 = 110.0 nH
L1 and L2 = 560.0 nH
10 F
≥15 ms
100 dBc/Hz
97 dBc/Hz
99 dBc/Hz
440 nF
≥600 s
99 dBc/Hz
96 dBc/Hz
98 dBc/Hz
CLK
POWER-UP
DATA
LE
R COUNTER
LATCH DATA
CONTROL
LATCH DATA
N COUNTER
LATCH DATA
REQUIRED INTERVAL
CONTROL LATCH WRITE TO
N COUNTER LATCH WRITE
07139-
033
Figure 26. Power-Up Timing
相關PDF資料 |
PDF描述 |
|---|---|
| RCM12DRYN-S13 | CONN EDGECARD 24POS .156 EXTEND |
| RCM12DRYH-S13 | CONN EDGECARD 24POS .156 EXTEND |
| HCM08DSEI-S13 | CONN EDGECARD 16POS .156 EXTEND |
| HBM08DSEI-S13 | CONN EDGECARD 16POS .156 EXTEND |
| ASPI-7318-2R5M-T | INDUCTOR SHIELD 2.5UH SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADF4602EB3Z | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits) |
| EVAL-ADF4602EB5Z | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits) |
| EVAL-ADF4XXXZ-USB | 功能描述:BOARD ADAPTER USB/PAR ADF4XXX RoHS:是 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF) |
| EVAL-ADF5000EB2Z | 功能描述:BOARD EVAL FOR ADF5000 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-ADF5001EB2Z | 制造商:Analog Devices 功能描述:EVALUATION BOARDS - Bulk |
發布緊急采購，3分鐘左右您將得到回復。