參數資料
型號: EVAL-ADF4360-9EBZ1
廠商: Analog Devices Inc
文件頁數: 3/24頁
文件大?。?/td> 0K
描述: EVALUATION BOARD FOR ADF4360-9
標準包裝: 1
主要目的: 計時,頻率合成器
嵌入式:
已用 IC / 零件: ADF4360-9
主要屬性: 帶 VCO 的單路整數-N PLL
次要屬性: 360MHz,1.6MHz PFD
已供物品:
其它名稱: Q5254840
Data Sheet
ADF4360-9
Rev. C | Page 11 of 24
The truth table for these bits is shown in Table 5. Figure 22
shows a summary of how the latches are programmed. Note
that the test modes latch is used for factory testing and should
not be programmed by the user.
Table 5. C2 and C1 Truth Table
Control Bits
Data Latch
C2
C1
0
Control
0
1
R Counter
1
0
N Counter (B)
1
Test Modes
VCO
The VCO core in the ADF4360 family uses eight overlapping
bands, as shown in Figure 18, to allow a wide frequency range
to be covered without a large VCO sensitivity (KV) and resultant
poor phase noise and spurious performance.
The correct band is chosen automatically by the band select
logic at power-up or whenever the N counter latch is updated.
It is important that the correct write sequence be followed at
power-up. The correct write sequence is as follows:
1. R Counter Latch
2. Control Latch
3. N Counter Latch
During band selection, which takes five PFD cycles, the VCO
VTUNE is disconnected from the output of the loop filter and
connected to an internal reference voltage.
0
1.0
0.5
2.5
2.0
1.5
3.5
3.0
80
85
90
100
95
105
115
110
FREQUENCY (MHz)
V
T
UNE
(V)
07139-
019
Figure 18. VTUNE, ADF4360-9, L1 and L2 = 270 nH vs. Frequency
The R counter output is used as the clock for the band select
logic and should not exceed 1 MHz. A programmable divider is
provided at the R counter input to allow division by 1, 2, 4, or 8
and is controlled by the BSC1 bit and the BSC2 bit in the R counter
latch. Where the required PFD frequency exceeds 1 MHz, the
divide ratio should be set to allow enough time for correct band
selection. For many applications, it is usually best to set this to 8.
After band selection, normal PLL action resumes. The value of
KV is determined by the value of the inductors used (see the
family contains linearization circuitry to minimize any variation
of the product of ICP and KV.
The operating current in the VCO core is programmable in four
steps: 2.5 mA, 5 mA, 7.5 mA, and 10 mA. This is controlled by
the PC1 bit and the PC2 bit in the control latch.
It is strongly recommended that only the 5 mA setting be used.
However, in applications requiring a low VCO frequency, the
high temperature coefficient of some inductors may lead to the
VCO tuning voltage varying as temperature changes. The 7.5 mA
VCO core power setting shows less tuning voltage variation over
temperature in these applications and can be used, provided that
240 resistors are used in parallel with Pin 9 and Pin 10, instead of
the default 470 .
相關PDF資料
PDF描述
RCM12DRYN-S13 CONN EDGECARD 24POS .156 EXTEND
RCM12DRYH-S13 CONN EDGECARD 24POS .156 EXTEND
HCM08DSEI-S13 CONN EDGECARD 16POS .156 EXTEND
HBM08DSEI-S13 CONN EDGECARD 16POS .156 EXTEND
ASPI-7318-2R5M-T INDUCTOR SHIELD 2.5UH SMD
相關代理商/技術參數
參數描述
EVAL-ADF4602EB3Z 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits)
EVAL-ADF4602EB5Z 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits)
EVAL-ADF4XXXZ-USB 功能描述:BOARD ADAPTER USB/PAR ADF4XXX RoHS:是 類別:編程器,開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF)
EVAL-ADF5000EB2Z 功能描述:BOARD EVAL FOR ADF5000 RoHS:是 類別:編程器,開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:- 主要目的:電信,線路接口單元(LIU) 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板,電源,線纜,CD 其它名稱:82EBV2081
EVAL-ADF5001EB2Z 制造商:Analog Devices 功能描述:EVALUATION BOARDS - Bulk