- 您現在的位置：買賣IC網 > PDF目錄16231 > EVAL-ADF4360-8EBZ1 (Analog Devices Inc)BOARD EVALUATION FOR ADF4360-8 PDF資料下載
參數資料
| 型號： | EVAL-ADF4360-8EBZ1 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 22/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR ADF4360-8 |
| 標準包裝： | 1 |
| 主要目的： | 計時，頻率合成器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ADF4360-8 |
| 主要屬性： | 帶 VCO 的單路整數-N PLL |
| 次要屬性： | 120MHz，1MHz PFD |
| 已供物品： | 板，線纜，軟件 |
| 相關產品： | ADF4360-8BCPZ-ND - IC SYNTHESIZER VCO 24-LFCSP ADF4360-8BCPZRL7TR-ND - IC SYNTHESIZER VCO 24LFCSP ADF4360-8BCPZRL-ND - IC SYNTHESIZER VCO 24LFCSP |
| 其它名稱： | Q4990657 |
ADF4360-8
Rev. A | Page 7 of 24
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
ADF4360-8
TOP VIEW
(Not to Scale)
CPGND
1
AVDD 2
AGND
3
RFOUTA 4
RFOUTB 5
VVCO 6
DATA
18
CLK
17
REFIN
16
DGND
15
CN
14
RSET
13
V
TUNE
7
AGND
8
L1
9
L2
10
AGND
11
C
12
CP
24
CE
23
AGND
22
DV
DD
21
MUX
O
U
T
20
LE
19
04763-003
PIN 1
IDENTIFIER
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
Mnemonic
Description
1
CPGND
Charge Pump Ground. This is the ground return path for the charge pump.
2
AVDD
Analog Power Supply. This ranges from 3.0 V to 3.6 V. Decoupling capacitors to the analog ground plane should be
placed as close as possible to this pin. AVDD must have the same value as DVDD.
3, 8, 11, 22
AGND
Analog Ground. This is the ground return path of the prescaler and VCO.
4
RFOUTA
VCO Output. The output level is programmable from 0 dBm to
9 dBm. See the Output Matching section for a
description of the various output stages.
5
RFOUTB
VCO Complementary Output. The output level is programmable from 0 dBm to 9 dBm. See the Output Matching
section for a description of the various output stages.
6
VVCO
Power Supply for the VCO. This ranges from 3.0 V to 3.6 V. Decoupling capacitors to the analog ground plane should
be placed as close as possible to this pin. VVCO must have the same value as AVDD.
7
VTUNE
Control Input to the VCO. This voltage determines the output frequency and is derived from filtering the CP
output voltage.
9
L1
An external inductor to AGND should be connected to this pin to set the ADF4360-8 output frequency. L1 and L2
need to be the same value. A 470 resistor should be added in parallel to AGND.
10
L2
An external inductor to AGND should be connected to this pin to set the ADF4360-8 output frequency. L1 and L2
need to be the same value. A 470 resistor should be added in parallel to AGND.
12
CC
Internal Compensation Node. This pin must be decoupled to ground with a 10 nF capacitor.
13
RSET
Connecting a resistor between this pin and CPGND sets the maximum charge pump output current for the synthesizer.
The nominal voltage potential at the RSET pin is 0.6 V. The relationship between ICP and RSET is
SET
CPmax
R
I
75
.
11
=
where RSET = 4.7 k, ICPmax = 2.5 mA.
14
CN
Internal Compensation Node. This pin must be decoupled to VVCO with a 10 F capacitor.
15
DGND
Digital Ground.
16
REFIN
Reference Input. This is a CMOS input with a nominal threshold of VDD/2 and a dc equivalent input resistance of
100 k (see Figure 16). This input can be driven from a TTL or CMOS crystal oscillator, or it can be ac-coupled.
17
CLK
Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is latched into the 24-bit
shift register on the CLK rising edge. This input is a high impedance CMOS input.
18
DATA
Serial Data Input. The serial data is loaded MSB first with the two LSBs being the control bits. This input is a high
impedance CMOS input.
19
LE
Load Enable, CMOS Input. When LE goes high, the data stored in the shift registers is loaded into one of the four
latches, and the relevant latch is selected using the control bits.
20
MUXOUT
This multiplexer output allows either the lock detect, the scaled RF, or the scaled reference frequency to be
accessed externally.
21
DVDD
Digital Power Supply. This ranges from 3.0 V to 3.6 V. Decoupling capacitors to the digital ground plane should be
placed as close as possible to this pin. DVDD must have the same value as AVDD.
23
CE
Chip Enable. A logic low on this pin powers down the device and puts the charge pump into three-state mode.
Taking the pin high powers up the device depending on the status of the power-down bits.
24
CP
Charge Pump Output. When enabled, this provides ±ICP to the external loop filter, which in turn drives the internal VCO.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J7X-EY-S | CONVERTER MOD DC/DC 5.2V 50W |
| MCP73213-B6SI/MF | IC LI-ION/LI-POLY CTRLR 10-DFN |
| VE-J7W-EZ-F4 | CONVERTER MOD DC/DC 5.5V 25W |
| VE-J7W-EZ-F2 | CONVERTER MOD DC/DC 5.5V 25W |
| VE-J7W-EZ-F1 | CONVERTER MOD DC/DC 5.5V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADF4360-9EBZ1 | 功能描述:EVALUATION BOARD FOR ADF4360-9 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-ADF4602EB3Z | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits) |
| EVAL-ADF4602EB5Z | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits) |
| EVAL-ADF4XXXZ-USB | 功能描述:BOARD ADAPTER USB/PAR ADF4XXX RoHS:是 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF) |
| EVAL-ADF5000EB2Z | 功能描述:BOARD EVAL FOR ADF5000 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
發布緊急采購，3分鐘左右您將得到回復。