- 您現在的位置：買賣IC網 > PDF目錄16232 > EVAL-ADF4360-1EBZ1 (Analog Devices Inc)BOARD EVALUATION FOR ADF4360-1 PDF資料下載
參數資料
| 型號： | EVAL-ADF4360-1EBZ1 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 22/24頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR ADF4360-1 |
| 標準包裝： | 1 |
| 主要目的： | 計時，頻率合成器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ADF4360-1 |
| 主要屬性： | 帶 VCO 的單路整數-N PLL |
| 次要屬性： | 2.25GHz，200kHz PFD |
| 已供物品： | 板，線纜，軟件 |
| 相關產品： | ADF4360-1BCPZ-ND - IC SYNTHESIZER VCO 24-LFCSP ADF4360-1BCPZRL7-ND - IC SYNTHESIZER VCO 24LFCSP ADF4360-1BCPZRL-ND - IC SYNTHESIZER VCO 24LFCSP |
| 其它名稱： | Q4875592 Q5594761 |
Data Sheet
ADF4360-1
Rev. C | Page 7 of 24
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
04414-
003
ADF4360-1
TOP VIEW
(Not to Scale)
CPGND
1
AVDD 2
AGND
3
RFOUTA 4
RFOUTB 5
VVCO 6
DATA
18
CLK
17
REFIN
16
DGND
15
CN
14
RSET
13
V
T
UNE
7
AG
ND
8
AG
ND
9
AG
ND
10
AG
ND
11
C
12
CP
24
CE
23
AG
ND
22
DV
DD
21
M
UX
O
UT
20
LE
19
PIN 1
IDENTIFIER
NOTES
1. THE EXPOSED PAD MUST BE CONNECTED TO AGND.
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
Mnemonic
Description
1
CPGND
Charge Pump Ground. This is the ground return path for the charge pump.
2
AV
DD
Analog Power Supply. This ranges from 3.0 V to 3.6 V. Decoupling capacitors to the analog ground plane
should be placed as close as possible to this pin. AV
DD must have the same value as DVDD.
3, 8 to 11, 22
AGND
Analog Ground. This is the ground return path of the prescaler and VCO.
4
RF
OUTA
VCO Output. The output level is programmable from 6 dBm to 13 dBm. See the Output Matching section
for a description of the various output stages.
5
RF
OUTB
VCO Complementary Output. The output level is programmable from 6 dBm to 13 dBm. See the Output
Matching section for a description of the various output stages.
6
V
VCO
Power Supply for the VCO. This ranges from 3.0 V to 3.6 V. Decoupling capacitors to the analog ground plane
should be placed as close as possible to this pin. V
VCO must have the same value as AVDD.
7
V
TUNE
Control Input to the VCO. This voltage determines the output frequency and is derived from filtering the CP
output voltage.
12
C
Internal Compensation Node. This pin must be decoupled to ground with a 10 nF capacitor.
13
R
SET
Connecting a resistor between this pin and CP
GND sets the maximum charge pump output current for the
synthesizer. The nominal voltage potential at the R
SET pin is 0.6 V. The relationship between ICP and RSET is
SET
CPmax
R
I
75
.
11
=
where R
SET = 4.7 k, ICPMAX = 2.5 mA.
14
C
N
Internal Compensation Node. This pin must be decoupled to V
VCO with a 10 F capacitor.
15
DGND
Digital Ground.
16
REF
IN
Reference Input. This is a CMOS input with a nominal threshold of V
DD/2 and a dc equivalent input resistance of
100 k. See Figure 10. This input can be driven from a TTL or CMOS crystal oscillator or it can be ac-coupled.
17
CLK
Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is latched into
the 24-bit shift register on the CLK rising edge. This input is a high impedance CMOS input.
18
DATA
Serial Data Input. The serial data is loaded MSB first with the two LSBs being the control bits. This input is a
high impedance CMOS input.
19
LE
Load Enable, CMOS Input. When LE goes high, the data stored in the shift registers is loaded into one of the
four latches, and the relevant latch is selected using the control bits.
20
MUXOUT
This multiplexer output allows either the lock detect, the scaled RF, or the scaled reference frequency to be
accessed externally.
21
DV
DD
Digital Power Supply. This ranges from 3.0 V to 3.6 V. Decoupling capacitors to the digital ground plane
should be placed as close as possible to this pin. DV
DD must have the same value as AVDD.
23
CE
Chip Enable. A logic low on this pin powers down the device and puts the charge pump into three-state
mode. Taking the pin high powers up the device depending on the status of the power-down bits.
24
CP
Charge Pump Output. When enabled, this provides ± I
CP to the external loop filter, which in turn drives the
internal VCO.
EP
Exposed Pad. The exposed pad must be connected to AGND.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J7V-EZ-F1 | CONVERTER MOD DC/DC 5.8V 25W |
| M3WWK-1440K | IDC CABLE - MPL14K/MC14F/MPL14K |
| MCP73223-C2SI/MF | IC LI IRON PHOSPHATE CTRLR 10DFN |
| VE-J7V-EY-S | CONVERTER MOD DC/DC 5.8V 50W |
| M3KKK-1440K | IDC CABLE - MPK14K/MC14F/MPK14K |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADF4360-2EB1 | 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR ADF4360-2 |
| EVAL-ADF4360-2EBZ1 | 功能描述:BOARD EVALUATION FOR ADF4360-2 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| EVAL-ADF4360-3EB1 | 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR ADF4360-3 |
| EVAL-ADF4360-4EB1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated Synthesizer and VCO |
| EVAL-ADF4360-4EBZ1 | 制造商:Analog Devices 功能描述:Evaluation Board Integrated Synthesizer And VCO 制造商:Analog Devices 功能描述:Evaluation Board I.C. |
發布緊急采購，3分鐘左右您將得到回復。