- 您現在的位置：買賣IC網 > PDF目錄17070 > EVAL-AD5382EBZ (Analog Devices Inc)BOARD EVAL FOR AD5382 PDF資料下載
參數資料
| 型號： | EVAL-AD5382EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 20/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD5382 |
| 產品培訓模塊： | DAC Architectures |
| 標準包裝： | 1 |
| DAC 的數量： | 32 |
| 位數： | 14 |
| 采樣率（每秒）： | 125k |
| 數據接口： | DSP，I²C，MICROWIRE?，并行，QSPI?，SPI? |
| 設置時間： | 8µs |
| DAC 型： | 電壓 |
| 工作溫度： | -40°C ~ 85°C |
| 已供物品： | 板，CD |
| 已用 IC / 零件： | AD5382 |
| 其它名稱： | Q4391457 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Data Sheet
AD5382
Rev. C | Page 27 of 40
Daisy-Chain Mode
For systems that contain several devices, the SDO pin can be
used to daisy-chain several devices together. This daisy-chain
mode can be useful in system diagnostics and in reducing the
number of serial interface lines.
By connecting the DCEN (daisy-chain enable) pin high, daisy-
chain mode is enabled. The first falling edge of SYNC starts the
write cycle. The SCLK is continuously applied to the input shift
register when SYNC is low. If more than 24 clock pulses are
applied, the data ripples out of the shift register and appears
on the SDO line. This data is clocked out on the rising edge of
SCLK and is valid on the falling edge. By connecting the SDO
of the first device to the DIN input on the next device in the
chain, a multidevice interface is constructed. Twenty-four clock
pulses are required for each device in the system. Therefore, the
total number of clock cycles must equal 24N, where N is the
total number of AD538x devices in the chain.
When the serial transfer to all devices is complete, SYNC is
taken high. This latches the input data in each device in the
daisy-chain and prevents further data from being clocked into
the input shift register.
If the SYNC is taken high before 24 clocks are clocked into the
part, this is considered a bad frame and the data is discarded.
The serial clock can be either a continuous or a gated clock. A
continuous SCLK source can be used only if SYNC can be held
low for the correct number of clock cycles. In gated clock mode,
a burst clock containing the exact number of clock cycles must
be used, and SYNC must be taken high after the final clock to
latch the data.
Readback Mode
Readback mode is invoked by setting the R/W bit = 1 in the
serial input register write. With R/W = 1, Bits A4 to A0, in
association with Bits REG1 and REG0, select the register to be
read. The remaining data bits in the write sequence are don’t
cares. During the next SPI write, the data appearing on the SDO
output contains the data from the previously addressed register.
For a read of a single register, the NOP command can be used
in clocking out the data from the selected register on SDO.
Figure 29 shows the readback sequence. For example, to read
back the m register of Channel 0 on the AD5382, the following
sequence should be implemented. First, write 0x404XXX to the
AD5382 input register. This configures the AD5382 for read
mode with the m register of Channel 0 selected. Data Bits DB13
to DB0 are don’t cares. Follow this with a second write, a NOP
condition, 0x000000. During this write, the data from the m
register is clocked out on the DOUT line, that is, data clocked
out contains the data from the m register in Bits DB13 to DB0,
and the top 10 bits contain the address information as
previously written. In readback mode, the SYNC signal must
frame the data. Data is clocked out on the rising edge of SCLK
and is valid on the falling edge of the SCLK signal. If the SCLK
idles high between the write and read operations of a readback
operation, the first bit of data is clocked out on the falling edge
of SYNC.
03733
-0
30
24
48
SCLK
SYNC
DIN
SDO
UNDEFINED
SELECTED REGISTER DATA CLOCKED OUT
NOP CONDITION
INPUT WORD SPECIFIES REGISTER TO BE READ
DB23
DB0
DB23
DB0
DB23
Figure 29. Serial Readback Operation
相關PDF資料 |
PDF描述 |
|---|---|
| NR5040T220M | INDUCTOR 22UH 1.4A 20% SMD |
| EVAL-AD5061EBZ | BOARD EVALUATION AD5061 |
| V375C2E50BG2 | CONVERTER MOD DC/DC 2V 50W |
| DC1010A-B | BOARD DELTA SIGMA ADC LTC2489 |
| EVAL-AD5621EBZ | BOARD EVALUATION FOR AD5621 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD5383EB | 制造商:Analog Devices 功能描述:EVAL KIT FOR 32CH, 3V/5 V, SGL-SUPPLY, 12-BIT, VOLT OUTPUT D - Bulk 制造商:Rochester Electronics LLC 功能描述: |
| EVAL-AD5390EB | 制造商:Analog Devices 功能描述: |
| EVAL-AD5390EBZ | 功能描述:BOARD EVALUATION FOR AD5390 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5391EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk 制造商:Rochester Electronics LLC 功能描述: |
| EVAL-AD5391EBZ | 功能描述:BOARD EVALUATION FOR AD5391 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
發布緊急采購，3分鐘左右您將得到回復。