參數資料
型號: DTMFDECODER-RD
廠商: Silicon Laboratories Inc
文件頁數: 42/178頁
文件大?。?/td> 0K
描述: KIT REF DESIGN DTMF DECODER
應用說明: DTMF Decoder Ref Design AppNote
標準包裝: 1
主要目的: 電信,DTMF 解碼器
嵌入式:
已用 IC / 零件: C8051F300
主要屬性: 8kHz 采樣速率模數轉換器
次要屬性: 16 個 Goertzel 濾波器
已供物品: 板,軟件
產品目錄頁面: 627 (CN2011-ZH PDF)
相關產品: 336-1535-5-ND - IC 8051 MCU 8K FLASH 14-SOIC
C8051F300-GMR-ND - IC 8051 MCU 8K FLASH 11QFN
336-1245-ND - IC 8051 MCU 8K FLASH 11QFN
其它名稱: 336-1283
C8051F300/1/2/3/4/5
136
Rev. 2.9
SFR Definition 14.1.
Bit7:
S0MODE: Serial Port 0 Operation Mode.
This bit selects the UART0 Operation Mode.
0: Mode 0: 8-bit UART with Variable Baud Rate
1: Mode 1: 9-bit UART with Variable Baud Rate
Bit6:
UNUSED. Read = 1b. Write = don’t care.
Bit5:
MCE0: Multiprocessor Communication Enable.
The function of this bit is dependent on the Serial Port 0 Operation Mode.
Mode 0: Checks for valid stop bit.
0: Logic level of stop bit is ignored.
1: RI0 will only be activated if stop bit is logic level 1.
Mode 1: Multiprocessor Communications Enable.
0: Logic level of ninth bit is ignored.
1: RI0 is set and an interrupt is generated only when the ninth bit is logic 1.
Bit4:
REN0: Receive Enable.
This bit enables/disables the UART receiver.
0: UART0 reception disabled.
1: UART0 reception enabled.
Bit3:
TB80: Ninth Transmission Bit.
The logic level of this bit will be assigned to the ninth transmission bit in 9-bit UART Mode. It
is not used in 8-bit UART Mode. Set or cleared by software as required.
Bit2:
RB80: Ninth Receive Bit.
RB80 is assigned the value of the STOP bit in Mode 0; it is assigned the value of the 9th
data bit in Mode 1.
Bit1:
TI0: Transmit Interrupt Flag.
Set by hardware when a byte of data has been transmitted by UART0 (after the 8th bit in 8-
bit UART Mode, or at the beginning of the STOP bit in 9-bit UART Mode). When the UART0
interrupt is enabled, setting this bit causes the CPU to vector to the UART0 interrupt service
routine. This bit must be cleared manually by software
Bit0:
RI0: Receive Interrupt Flag.
Set to ‘1’ by hardware when a byte of data has been received by UART0 (set at the STOP bit
sampling time). When the UART0 interrupt is enabled, setting this bit to ‘1’ causes the CPU
to vector to the UART0 interrupt service routine. This bit must be cleared manually by soft-
ware.
R/W
Reset Value
S0MODE
MCE0
REN0
TB80
RB80
TI0
RI0
01000000
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
SFR Address:
(bit addressable)
0x98
SCON0: Serial Port 0 Control
相關PDF資料
PDF描述
UPZ2E121MND9 CAP ALUM 120UF 250V 20% RADIAL
A3KKB-1036M IDC CABLE - APK10B/AE10M/APK10B
UVR2G101MRD6 CAP ALUM 100UF 400V 20% RADIAL
LLS2A102MELZ CAP ALUM 1000UF 100V 20% SNAP
SI5310-EVB BOARD EVALUATION FOR SI5310
相關代理商/技術參數
參數描述
DTMG5812L WAF 制造商:ON Semiconductor 功能描述:
DTMG5852L WAF 制造商:ON Semiconductor 功能描述:
DTMH04-2PA 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE DTM HI TEMP A KEY 2WAY 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE, DTM HI TEMP, A KEY, 2WAY, Series:DTMH, No. of Positions:2, Gender:Receptacle, No. of Rows:1 , RoHS Compliant: Yes
DTMH04-2PB 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE DTM HI TEMP B KEY 2WAY 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE, DTM HI TEMP, B KEY, 2WAY 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE, DTM HI TEMP, B KEY, 2WAY; Series:DTMH; Gender:Receptacle; No. of Contacts:2; No. of Rows:1; Contact Gender:Pin; Connector Mounting:Cable; Connector Shell Size:-; Contact Termination:Crimp; Contact Material:Copper; Contact;RoHS Compliant: Yes
DTMH04-2PC 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE DTM HI TEMP C KEY 2WAY 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE, DTM HI TEMP, C KEY, 2WAY 制造商:TE Connectivity / Deutsch 功能描述:RECEPTACLE, DTM HI TEMP, C KEY, 2WAY; Series:DTMH; Gender:Receptacle; No. of Contacts:2; No. of Rows:1; Contact Gender:Pin; Connector Mounting:Cable; Connector Shell Size:-; Contact Termination:Crimp; Contact Material:Copper; Contact;RoHS Compliant: Yes