參數資料
型號: DSP56F801FA80E
廠商: Freescale Semiconductor
文件頁數: 16/48頁
文件大?。?/td> 0K
描述: IC DSP 60MHZ 16KB FLASH 48-LQFP
標準包裝: 250
系列: 56F8xx
核心處理器: 56800
芯體尺寸: 16-位
速度: 80MHz
連通性: SCI,SPI
外圍設備: POR,PWM,WDT
輸入/輸出數: 11
程序存儲器容量: 20KB(10K x 16)
程序存儲器類型: 閃存
RAM 容量: 2K x 16
電壓 - 電源 (Vcc/Vdd): 3 V ~ 3.6 V
數據轉換器: A/D 8x12b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 48-LQFP
包裝: 托盤
External Clock Operation
56F801 Technical Data, Rev. 17
Freescale Semiconductor
23
Figure 3-6 Flash Mass Erase Cycle
3.5 External Clock Operation
The 56F801 device clock is derived from either 1) an internal crystal oscillator circuit working in
conjunction with an external crystal, 2) an external frequency source, or 3) an on-chip relaxation oscillator.
To generate a reference frequency using the internal crystal oscillator circuit, a reference crystal external
to the chip must be connected between the EXTAL and XTAL pins. Paragraphs 3.5.1 and 3.5.4 describe
these methods of clocking. Whichever type of clock derivation is used provides a reference signal to a
phase-locked loop (PLL) within the 56F801. In turn, the PLL generates a master reference frequency that
determines the speed at which chip operations occur.
Application code can be set to change the frequency source between the relaxation oscillator and crystal
oscillator or external source, and power down the relaxation oscillator if desired. Selection of which clock
is used is determined by setting the PRECS bit in the PLLCR (phase-locked loop control register) word
(bit 2). If the bit is set to 1, the external crystal oscillator circuit is selected. If the bit is set to 0, the internal
relaxation oscillator is selected, and this is the default value of the bit when power is first applied.
3.5.1
Crystal Oscillator
The internal oscillator is also designed to interface with a parallel-resonant crystal resonator in the
frequency range specified for the external crystal in Table 3-10. Figure 3-7 shows a recommended crystal
oscillator circuit. Follow the crystal supplier’s recommendations when selecting a crystal, since crystal
parameters determine the component values required to provide maximum stability and reliable start-up.
The crystal and associated components should be mounted as close as possible to the EXTAL and XTAL
pins to minimize output distortion and start-up stabilization time. The internal 56F80x oscillator circuitry
XADR
YE=SE=OE=0
ERASE
NVSTR
Tnvs
Tnvh1
Trcv
Tme
MAS1
IFREN
XE
相關PDF資料
PDF描述
DSP56F802TA80E IC DSP 60MHZ 16KB FLASH 32-LQFP
DSP56F803BU80E IC DSP 80MHZ 64KB FLASH 100LQFP
DSP56F805FV80E IC DSP 80MHZ 64KB FLASH 144LQFP
DSP56F807VF80E IC DSP 80MHZ 60K FLASH 160-BGA
DSP56F826BU80 IC DSP 80MHZ 64KB FLASH 100LQFP
相關代理商/技術參數
參數描述
DSP56F801FA80E 制造商:Freescale Semiconductor 功能描述:IC
DSP56F801PB 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-bit Digital Signal Processor
DSP56F802 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controllers
DSP56F802PB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:56F802 16-Bit Hybrid Controller Product Brief
DSP56F802TA60 功能描述:數字信號處理器和控制器 - DSP, DSC 60Mhz/30MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT