- 您現在的位置：買賣IC網 > PDF目錄376805 > DMC73C167 8Bit Single Chip Microcontroller PDF資料下載
參數資料
| 型號： | DMC73C167 |
| 英文描述： | 8Bit Single Chip Microcontroller |
| 中文描述： | 8位單芯片微控制器 |
| 文件頁數： | 36/90頁 |
| 文件大?。?/td> | 742K |
| 代理商： | DMC73C167 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁
36
8Bit Single Chip Microcontroller
DMC73C167
1) The port using as the interrupt input should be in the input mode. The output mode may
cause damage to the device. If the contents of the corresponding output port are changed
from 1 to 0, the interrupt flag will also set to 1.
2) If not used as the interrupt input, the corresponding interrupt enable should be disabled.
But even with the disabling of this interrupt enable, the interrupt flag will be changed.
The external interrupt timing is shown in Figure 5-6. The device needs additional circuitry
when INT1, INT3_0, and IN 5_0 are used as zero-cross detectors as shown in Figure 5-7.
The following conditions are needed :
1) The external interrupt level should be in the range from VCC +0.3V to VSS. The input
current must not exceed the specification.
2) Noise on the interrupt signal should be minimized because the noise debounce logic is not
implemented on chip. The function may fail due to continuous interrupts.
Caution :
It is possible that the INTn flag bits in the IOCNT registers could be unintentionally cleared by
using bit manipulation instructions (ANDP/ORP & XORP). To avoid these occurences, use
the MOVP and STA instructions when writing Data to IOCNT registers.
Figure 5-3. External Interrupt Timing
VCC
VSS
External
Input
VT+
VT-
Interrupt
Happen
Last
Happen
1
0
Interrupt
Execution
￡￡á￡￡×￡￡
相關PDF資料 |
PDF描述 |
|---|---|
| DMC73C168 | 8Bit Single Chip Microcontroller |
| DMC80C49 | CMOS SINGLE-COMPONENT 8-BIT MICROCOMPUTER |
| DMCA1CHP | TRANSISTOR | MOSFET | ARRAY | N-CHANNEL | 20V V(BR)DSS | 50MA I(D) | CHIP |
| DMCB1CHP | TRANSISTOR | MOSFET | N-CHANNEL | 30V V(BR)DSS | 50MA I(D) | CHIP |
| DMCB2CHP | TRANSISTOR | MOSFET | N-CHANNEL | 30V V(BR)DSS | 50MA I(D) | CHIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DMC73C168 | 制造商:DAEWOO 制造商全稱:DAEWOO 功能描述:8Bit Single Chip Microcontroller |
| DMC757 | 制造商:Daniels Manufacturing Corporation (DMC) 功能描述:CONNECTOR |
| DMC-8/16-15 | 制造商:Brady Corporation 功能描述: |
| DMC-8/16-30 | 制造商:Brady Corporation 功能描述: |
| DMC80C49 | 制造商:DAEWOO 制造商全稱:DAEWOO 功能描述:CMOS SINGLE-COMPONENT 8-BIT MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。