- 您現在的位置：買賣IC網 > PDF目錄17070 > DC1011A-B (Linear Technology)BOARD DELTA SIGMA ADC LTC2496 PDF資料下載
參數資料
| 型號： | DC1011A-B |
| 廠商： | Linear Technology |
| 文件頁數： | 5/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2496 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC1011A Schematic DC1011A Design Files |
| 標準包裝： | 1 |
| 系列： | Easy Drive™, QuikEval™ |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 6.9 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 已用 IC / 零件： | LTC2496 |
| 已供物品： | 板 |
| 相關產品： | LTC2496CUHF#TRPBF-ND - IC ADC 16BIT DELTA SIG 38-QFN LTC2496IUHF#TRPBF-ND - IC ADC 16BIT DELTA SIG 38-QFN LTC2496CUHF#PBF-ND - IC ADC 16BIT DELTA SIG 38-QFN LTC2496IUHF#PBF-ND - IC ADC 16BIT DELTA SIG 38-QFN |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC2496
2496fb
applicaTions inForMaTion
In order to achieve optimum performance, if an external
amplifier is not used, short these pins directly together
(ADCINP to MUXOUTP and ADCINN to MUXOUTN) and
minimize their capacitance to ground.
SERIAL INTERFACE PINS
The LTC2496 transmits the conversion result, reads the
input channel selection, and receives a start of conversion
command through a synchronous 3- or 4-wire interface.
Duringtheconversionandsleepstates,thisinterfacecanbe
usedtoaccesstheconverterstatus.Duringthedataoutput
state, it is used to read the conversion result and program
the input channel for the next conversion cycle.
Serial Clock Input/Output (SCK)
The serial clock pin (SCK) is used to synchronize the data
input/output transfer. Each bit is shifted out of the SDO
pin on the falling edge of SCK and data is shifted into the
SDI pin on the rising edge of SCK.
The serial clock pin (SCK) can be configured as either a
master (SCK is an output generated internally) or a slave
(SCK is an input and applied externally). Master mode
(Internal SCK) is selected by simply floating the SCK pin.
Slave mode (External SCK) is selected by driving SCK low
during power up and each falling edge of CS. Specific
details of these SCK modes are described in the Serial
Interface Timing Modes section.
Serial Data Output (SDO)
The serial data output pin (SDO) provides the result of the
last conversion as a serial bit stream (MSB first) during
the data output state. In addition, the SDO pin is used as
an end of conversion indicator during the conversion and
sleep states.
When CS is HIGH, the SDO driver is switched to a high
impedance state in order to share the data output line with
other devices. If CS is brought LOW during the conversion
phase, the EOC bit (SDO pin) will be driven HIGH. Once
the conversion is complete, if CS is brought LOW EOC will
be driven LOW indicating the conversion is complete and
the result is ready to be shifted out of the device.
Chip Select (CS)
The active low CS pin is used to test the conversion status,
enable I/O data transfer, initiate a new conversion, control
the duration of the sleep state, and set the SCK mode.
At the conclusion of a conversion cycle, while CS is HIGH,
the device remains in a low power sleep state where the
supply current is reduced several orders of magnitude. In
order to exit the sleep state and enter the data output state,
CS must be pulled low. Data is now shifted out the SDO pin
under control of the SCK pin as described previously.
A new conversion cycle is initiated either at the conclusion
of the data output cycle (all 24 data bits read) or by pulling
CS HIGH any time between the first and 24th rising edges
of the serial clock (SCK). In this case, the data output is
aborted and a new conversion begins.
Serial Data Input (SDI)
Theserialdatainput(SDI)isusedtoselecttheinputchannel.
Data is shifted into the device during the data output/input
state on the rising edge of SCK while CS is low.
OUTPUT DATA FORMAT
The LTC2496 serial output stream is 24 bits long. The
first bit indicates the conversion status, the second bit is
always zero, and the third bit conveys sign information.
The next 17 bits are the conversion result, MSB first. The
remaining 4 bits are always LOW.
Bit 23 (first output bit) is the end of conversion (EOC)
indicator. This bit is available on the SDO pin during the
conversion and sleep states whenever CS is LOW. This
bit is HIGH during the conversion cycle, goes LOW once
the conversion is complete, and is HIGH-Z when CS is
HIGH.
Bit 22 (second output bit) is a dummy bit (DMY) and is
always LOW.
Bit21(thirdoutputbit)istheconversionresultsignindica-
tor (SIG). If the selected input (VIN = IN+ – IN–) is greater
than 0V, this bit is HIGH. If VIN < 0, this bit is LOW.
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD5501EBZ | BOARD EVAL FOR AD5501 |
| V24C48C50BL | CONVERTER MOD DC/DC 48V 50W |
| V24C36C50BL | CONVERTER MOD DC/DC 36V 50W |
| EVAL-AD5443EBZ | BOARD EVAL FOR AD5433 |
| DC1011A-A | BOARD DELTA SIGMA ADC LTC2498 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC1011A-C | 功能描述:BOARD DELTA SIGMA ADC LTC2494 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:Easy Drive™, QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC-1012 | 制造商:BCM Advanced Research 功能描述:BCM NANO-ITX POWER BOARD - Bulk |
| DC1012080 WAF | 制造商:ON Semiconductor 功能描述: |
| DC1012-103L | 制造商:Coilcraft Inc 功能描述:Power inductor, 10% tol, RoHS |
| DC1012-104L | 制造商:Coilcraft Inc 功能描述:Power inductor, 10% tol, RoHS |
發布緊急采購，3分鐘左右您將得到回復。