- 您現在的位置：買賣IC網 > PDF目錄17070 > DC1010A-C (Linear Technology)BOARD DELTA SIGMA ADC LTC2487 PDF資料下載
參數資料
| 型號： | DC1010A-C |
| 廠商： | Linear Technology |
| 文件頁數： | 6/32頁 |
| 文件大小： | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2487 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC1010A Design File DC1010A Schematic |
| 標準包裝： | 1 |
| 系列： | Easy Drive™, QuikEval™ |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 15 |
| 數據接口： | I²C，串行 |
| 已用 IC / 零件： | LTC2487 |
| 已供物品： | 板 |
| 相關產品： | LTC2487IDE#TRPBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2487CDE#TRPBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2487CDE#PBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2487IDE#PBF-ND - IC ADC 16BIT DELTA SIG 14-DFN |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC2487
14
2487fd
I2C INTERFACE
The LTC2487 communicates through an I2C interface. The
I2C interface is a 2-wire, open-drain interface supporting
multiple devices and multiple masters on a single bus. The
connected devices can only pull the data line (SDA) low
and can never drive it high. SDA is required to be externally
connected to the supply through a pull-up resistor. When
the data line is not being driven, it is high. Data on the
I2C bus can be transferred at rates up to 100kbits/s in the
standard mode and up to 400kbits/s in the fast mode. The
VCC power should not be removed from the device when
the I2C bus is active to avoid loading the I2C bus lines
through the internal ESD protection diodes.
Each device on the I2C bus is recognized by a unique
address stored in that device and can operate either as a
transmitter or receiver, depending on the function of the
device. In addition to transmitters and receivers, devices
can also be considered as masters or slaves when perform-
ing data transfers. A master is the device which initiates a
data transfer on the bus and generates the clock signals
to permit that transfer. Devices addressed by the master
are considered a slave.
The LTC2487 can only be addressed as a slave. Once ad-
dressed, it can receive conguration bits (channel selec-
tion, rejection mode, speed mode, gain) or transmit the
last conversion result. The serial clock line, SCL, is always
an input to the LTC2487 and the serial data line SDA is
bidirectional. The device supports the standard mode and
the fast mode for data transfer speeds up to 400kbits/s.
Figure 2 shows the denition of the I2C timing.
The Start and Stop Conditions
A Start (S) condition is generated by transitioning SDA from
high to low while SCL is high. The bus is considered to be
busy after the Start condition. When the data transfer is
nished, a Stop (P) condition is generated by transitioning
SDA from low to high while SCL is high. The bus is free
after a Stop is generated. Start and Stop conditions are
always generated by the master.
When the bus is in use, it stays busy if a Repeated Start
(Sr) is generated instead of a Stop condition. The repeated
Start timing is functionally identical to the Start and is
used for writing and reading from the device before the
initiation of a new conversion.
Data Transferring
After the Start condition, the I2C bus is busy and data
transfer can begin between the master and the addressed
slave. Data is transferred over the bus in groups of nine
bits, one byte followed by one acknowledge (ACK) bit.
The master releases the SDA line during the ninth SCL
clock cycle. The slave device can issue an ACK by pulling
SDA low or issue a Not Acknowledge (NAK) by leaving
the SDA line high impedance (the external pull-up resistor
will hold the line high). Change of data only occurs while
the clock line (SCL) is low.
DATA FORMAT
After a Start condition, the master sends a 7-bit address
followed by a read/write (R/W) bit. The R/W bit is 1 for
a read request and 0 for a write request. If the 7-bit ad-
Figure 2. Denition of Timing for Fast/Standard Mode Devices on the I2C Bus
APPLICATIONS INFORMATION
SDA
SCL
SSr
P
S
tHD(SDA)
tHD(DAT)
tSU(STA)
tSU(STO)
tSU(DAT)
tLOW
tHD(SDA)
tSP
tBUF
tr
tf
tr
tf
tHIGH
2487 F02
相關PDF資料 |
PDF描述 |
|---|---|
| V48C2E50BG2 | CONVERTER MOD DC/DC 2V 50W |
| AP2142SG-13 | IC PWR SW USB 2CH 0.5A 8-SOIC |
| EVAL-AD5382EBZ | BOARD EVAL FOR AD5382 |
| NR5040T220M | INDUCTOR 22UH 1.4A 20% SMD |
| EVAL-AD5061EBZ | BOARD EVALUATION AD5061 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC1010CA | 制造商:DIGITAL 功能描述: |
| DC1010EL07 WAF | 制造商:ON Semiconductor 功能描述: |
| DC-101-1 | 制造商:INTRONICS 制造商全稱:INTRONICS 功能描述:1 WATT SINGLE OUTPUT DC-DC CONVERTERS |
| DC1011A-A | 功能描述:BOARD DELTA SIGMA ADC LTC2498 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:Easy Drive™, QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC1011A-B | 功能描述:BOARD DELTA SIGMA ADC LTC2496 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:Easy Drive™, QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。