- 您現在的位置：買賣IC網 > PDF目錄17070 > DC1010A-C (Linear Technology)BOARD DELTA SIGMA ADC LTC2487 PDF資料下載
參數資料
| 型號： | DC1010A-C |
| 廠商： | Linear Technology |
| 文件頁數： | 5/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2487 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC1010A Design File DC1010A Schematic |
| 標準包裝： | 1 |
| 系列： | Easy Drive™, QuikEval™ |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 15 |
| 數據接口： | I²C，串行 |
| 已用 IC / 零件： | LTC2487 |
| 已供物品： | 板 |
| 相關產品： | LTC2487IDE#TRPBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2487CDE#TRPBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2487CDE#PBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2487IDE#PBF-ND - IC ADC 16BIT DELTA SIG 14-DFN |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC2487
13
2487fd
ampliers. The remaining common mode input current
is eliminated by either balancing the differential input im-
pedances or setting the common mode input equal to the
common mode reference (see the Automatic Differential
Input Current Cancellation section). This unique architec-
ture does not require on-chip buffers, thereby enabling
signals to swing beyond ground and VCC. Moreover, the
cancellation does not interfere with the transparent offset
and full-scale auto-calibration and the absolute accuracy
(full scale + offset + linearity + drift) is maintained even
with external RC networks.
Power-Up Sequence
The LTC2487 automatically enters an internal reset state
when the power supply voltage, VCC, drops below a
threshold of approximately 2.0V. This feature guarantees
the integrity of the conversion result and input channel
selection.
When VCC rises above this threshold, the converter creates
an internal power-on-reset (POR) signal with a duration
of approximately 4ms. The POR signal clears all internal
registers. The conversion immediately following a POR
cycle is performed on the input channels IN+ = CH0 and
IN– = CH1 with simultaneous 50Hz/60Hz rejection, 1x
output rate, and gain = 1. The rst conversion following a
POR cycle is accurate within the specication of the device
if the power supply voltage is restored to (2.7V to 5.5V)
before the end of the POR interval. A new input channel,
rejection mode, speed mode, temperature selection or
gain can be programmed into the device during this rst
data input/output cycle.
Reference Voltage Range
This converter accepts a truly differential external reference
voltage. The absolute/common mode voltage range for the
REF+ and REF– pins covers the entire operating range of
the device (GND to VCC). For correct converter operation,
VREF must be positive (REF+ > REF–).
The LTC2487 differential reference input range is 0.1V to
VCC. For the simplest operation, REF+ can be shorted to
VCC and REF– can be shorted to GND. The converter out-
put noise is determined by the thermal noise of the front
end circuits and, as such, its value in nanovolts is nearly
constant with reference voltage. A decrease in reference
voltage will not signicantly improve the converter’s effec-
tive resolution. On the other hand, a decreased reference
will improve the converter’s overall INL performance.
Input Voltage Range
The analog inputs are truly differential with an absolute,
common mode range for the CH0-CH3 and COM input pins
extending from GND – 0.3V to VCC + 0.3V. Outside these
limits, the ESD protection devices begin to turn on and the
errors due to input leakage current increase rapidly. Within
these limits, the LTC2487 converts the bipolar differential
input signal VIN = IN+ – IN– (where IN+ and IN– are the
selected input channels), from –FS = –0.5 VREF/Gain
to +FS = 0.5 VREF/Gain where VREF = REF+ – REF–.
Outside this range, the converter indicates the overrange
or the underrange condition using distinct output codes
(see Table 1).
In order to limit any fault current, resistors of up to 5k
may be added in series with the input. The effect of series
resistance on the converter accuracy can be evaluated from
the curves presented in the Input Current/Reference Cur-
rent sections. In addition, series resistors will introduce a
temperature dependent error due to input leakage current.
A 1nA input leakage current will develop a 1ppm offset
error on a 5k resistor if VREF = 5V. This error has a very
strong temperature dependency.
APPLICATIONS INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| V48C2E50BG2 | CONVERTER MOD DC/DC 2V 50W |
| AP2142SG-13 | IC PWR SW USB 2CH 0.5A 8-SOIC |
| EVAL-AD5382EBZ | BOARD EVAL FOR AD5382 |
| NR5040T220M | INDUCTOR 22UH 1.4A 20% SMD |
| EVAL-AD5061EBZ | BOARD EVALUATION AD5061 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC1010CA | 制造商:DIGITAL 功能描述: |
| DC1010EL07 WAF | 制造商:ON Semiconductor 功能描述: |
| DC-101-1 | 制造商:INTRONICS 制造商全稱:INTRONICS 功能描述:1 WATT SINGLE OUTPUT DC-DC CONVERTERS |
| DC1011A-A | 功能描述:BOARD DELTA SIGMA ADC LTC2498 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:Easy Drive™, QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC1011A-B | 功能描述:BOARD DELTA SIGMA ADC LTC2496 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:Easy Drive™, QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。